Silex technology SX-500-1402 manual Modifying TCP/IP Settings

Page 33

Parameter

Description

Settings

Default Setting

	number (required for E-Cable UDP
	mode only)

Ectmmsec	Cable connection time resolution	Enable, Disable	Disable

Ecudp	ECable UDP mode	Enable, Disable	Disable

Restoring Factory Default Settings

The factory default settings can be restored at any time To do this, hold down the Reset pushbutton for more than five seconds.

Modifying TCP/IP Settings

You can modify the TCP/IP settings using the web browser interface or the Serial Device Server Serial Device Server’s internal configuration console.

To modify TCP/IP settings:

1.You can configure the TCP/IP settings using the Web Page configuration. Simply log in using the Serial Device Server IP address and select TCP/IP.

Figure 2 TCP/IP Window

Advanced Configuration	Silex	Page 27
	Part Number 140-00188-210A

Image 33

Contents

SX-500-1402 Serial Device Server Trademarks Page Contents Figures Contents Silex Part Number 140-00188-210A Safety Precautions About This Reference GuideEmissions Disclaimer 2009.08.13 Lee Aydelotte Initial Release Revision HistorySX-500 IntroductionPort Name Description Logical PortsLED FIPS-140-2 Interface Physical Logical InterfaceConfiguration Required SettingWPA2 AES-CCMP Https Secure Operation Physical ProtectionInstalling the Serial Device Server Hardware Verify Package ContentsInstalling the Serial Device Server RS-232 connector pinouts and cabling Status Monitors Function State Monitoring Serial Device Server StatusBasic Configuration Requirements Chapter Configuring the Serial Device ServerTCP/IP Settings Wireless Configuration SettingsConfiguration Methods First-Time IP Address Configuration Ping ipaddress Using a Web Browser to Configure the Serial Device Server Silex Authentication Server Certificate You can skip the remainder of this chapter AD-HOC Init Exit DisabledSerial Port Emulator Chapter Using the Serial Device Server with Your ApplicationTelnet ipaddress portnumber Raw TCP connection RFC 2217 Remote Modem Control Support ECable ModeConsole Mode Switching Print Server ModeSET Port S1 Filter AT AT CommandsFactory Default Settings Chapter Advanced ConfigurationFactory Default Settings Parameter Description CTS/RTSParameter Description Settings Default Setting Modifying TCP/IP SettingsUsing AT Modem Commands TCP/IP Settings ParameterDNS AT Commands Parameter Description Standard AT Commands SupportedParameter Command Description Extended AT Commands Parameter DescriptionAT#Cset nw ssid silex#Csave Response Codes Numeric Code Description Response CodesChapter Troubleshooting Email Tech support support@silexamerica.com Chapter Product Specifications Product Specifications ComponentRadio Performance Specifications Parameter TCP Port Connections Parameter SpecificationsTCP Port Connections Port Destination DevicePSK Appendix a Advanced Security ConfigurationEAP Ttls LeapKey Selection Wireless Security Only Encryption Mode Wireless Security OnlyWEP Key Value Wireless Security Only Pre-Shared Key Wireless Security OnlyWired Authentication Type Wired Ethernet Networks Only Wireless Authentication Type Wireless Security OnlyAuthentication Attempts PasswordProduct Specifications Silex Part Number 140-00188-210A Wireless and Network Security Commands Appendix B Console CommandsNetwork Commands Description Signal Quality Signal Strength = Noise LevelCommand Description TLS PSKSET NW Ethauth Ttls TLS Peap SET NW KEY# CL NW BSsid Wifi RTS Threshold =SET NW RTS SET NW CertcnSET NW Certexp SET NW CERTCN2SET NW Certkey SET NW IDSET NW Wpagroup Enable Disable SET NW Inap PAPMSCHAPV2SET NW Realm SET NW Reset Port CommandsPort Commands Description XON/XOFFServer Information Commands Description Server Information CommandsCL Port S1 JOB SET Port S1 Size 7SET Snmp CONtact String SET SERVEr NAme NameSET Snmp LOCation string SH SerialService Commands Description Service CommandsBINARYP1 TwcffffffTEXTP1 TWCFFFFFFP14String Commands String CommandsTCP/IP Commands Description TCP/IP CommandsEnter LANGUAGE= POSTSCRIPT\0ASET ARP ENable DIsable All hosts permitted accessSET IP BAnner ENable DIsable SET IP Chksum ENable DIsableSET IP FTP Auto Bootp Rarp Dhcp StaticSET IP Http SET IP LPDSET IP Tftp SET IP TCPSH IP AutoXxxxxxS1A 9100 XxxxxxS1B 3001 Firmware Update Command Description Firmware UpdateMiscellaneous Commands Help CommandsMiscellaneous Commands Description Console Commands Silex Part Number 140-00188-210A Appendix C Firmware Update Procedures Firmware Update Procedures Silex Part Number 140-00188-210A Information for United States Users Appendix D Safety and Regulatory Notices FCC ID N6C-SX10WG Information for Canadian Users IC notice SX-500Declaration of Conformity CE SX-500 Information for European Users SX-500Silex Technology America, Inc Appendix E Silex Contact InformationSilex Technology Europe GmbH Silex Technology Beijing, IncSilex Technology America, Inc