NCR 7883 manual Scan Sample Tags, Upc-A

Page 21

NCR RealScan 7883 Installation and Owner Guide

Scan Sample Tags

Now you should scan some sample tags to verify that the RealScan 7883 is communicating with the host terminal. Following are four good tags that you can use. After verifying that the RealScan 7883 is communicating properly with the host terminal, continue with the installation.

Note: For maximum performance, full size labels must be used. The UPC Symbol Specification Manual gives the exact size requirements for UPC labels. If the bar height is less than specified, more precise presentation to the scanner is required, reducing productivity.

UPC-A

1

7 7 0 6 2

3 7 9 2 0

4

Code 39

1

7

7

0

6

2

3

7

9

2

0

Code 128

1 7 7 0 6 2 3 7 9 2 0

Interleaved 2 of 5

0 1 7 7 0 6 2 3 7 9 2 0

497-0424789 Release F

04/04

21 of 75

Image 21
Contents Information Products RSD-Atlanta RealScan Installation and Owner GuideContents Laser Safety Label Laser Module Label Laser Power Revision Record Obtaining Technical Assistance Obtaining Additional InformationNCR RealScan 7883 Mountings Step Installation InstructionsInstalling Power Supply and Interface Cables Connecting the Cables to an NCR RealScanStandard Interface Connection USB Interface Connection IBM HID NCR RealScan 7835/7836 Auxiliary RS-232 PortSpecial Installations RS-232 PeripheralsRealScan 7892 Bi-Modal Presentation Scanner Programming the RealScan RealScan 7832 ProgrammingRealScan 7837 Programming Factory Default RS232, 7 DATA, 1 STOP, Space Parity Setting Program Parameters and Verifying Host Connection Turning on the RealScanFlash Latest Firmware Programming the RealScan UPC/EAN Programming DefaultsBaud Rate Programming for USB Connection RS-232 CommunicationsIBM Communications RSS-14 Stacked Reduced Space SymbologyRSS Expanded RSS Expanded StackedMaking Other Program Changes Enabling RSSDisabling RSS UPC-A Scan Sample Tags01234 5 678 9 Determining Label QualityScan Zone Adjusting Screw Setting RealScan 7883 Scan ZoneVertical Pass-by Scanning Horizontal Pass-by ScanningVertical Presentation Scanning from Bottom Vertical Presentation Scanning from TopMounting the RealScan Rubber FeetPlastic Top Plate Plastic Top Plate ScannerC Latch Clip Mounting Screw Vertical Mounting Bracket Checkstand Cutout Checkpoint CableCable Clamps Operating the Scanner Cleaning the Scanner Green Status Tones Problem Indicator Correcting Scanner ProblemsThen supply again Interface Connector Interface InformationMost Common Interface Cables Communications Protocol Programming WorksheetCommunications Protocol Options 4 and B not supported yet Checkstand Hole RealScan 7883 Horizontal Mount FeaturesVentilation Requirements Checkstand Hole RealScan 7883 Flat MountInstallation Type Input Voltage L1, L2 Circuit Breakers Electrical WiringNCR Components NCR RealScan Mettler Toledo Scale, & Sensormatic ScanMaxTMHSSensormatic Components Mettler Toledo ComponentsSystem Construction Right-TO-Left ScanningLeft-To-Right Scanning Configuring the Scale Installing the Scanner Connecting Sensormatic Components Routing the Cables Completing the Installation Calibrating the Mettler Toledo Scale NCR RealScan 7883 Installation and Owner Guide Sensormatic Programmable Functions Sensormatic Deactivation IndicatorsTroubleshooting Scanner ProblemsScale Problems Sensormatic Deactivation Programming Worksheets Communications ProtocolGood Read Tone Bar Codes TimersCode Bar Codes Unique Identifier Label Identifiers21 RS-232 Parameters 20 RS-232 Parameters22 RS-232 Prefix Byte 23 RS-232 Terminator Byte24 RS-232 Communications Options Miscellaneous Parameters RealScan Ascii Code Chart Identification Labels Regulatory InformationNCR Corporation Duluth, Ga CE Mark ApplicabilityDeclaration of Conformity Laser Safety Laser Safety LabelLaser Module Label Laser Power Reset Volume AdjustmentDefault Programming TagsProgramming Mode Save and ResetEnd Diagnostic Mode RS-232 Temporary Service ModeAbort Mode Reset TalliesHex Firmware FlashingR0050 R0053 Hex a Hex B Hex CHex D Hex F Hex E