NCR 7883 manual USB Interface Connection

Page 9

NCR RealScan 7883 Installation and Owner Guide

7883-1000 USB Interface Connection

Connecting a RealScan 7883-1000 Scanner to a USB port on a host terminal requires a special cable. One end of the Dongle Adapter Cable connects to the host terminal. The other end has an Interface Box that contains a printed circuit board with all the necessary circuitry. The host terminal supplies power for this circuitry. An Interface cable connects the scanner to this box. A Power Supply connected to the scanner is required for all configurations.

Interface Cable

Host Terminal

RealScan 7883

CD

RealScan 7837

Power Supply

Power Cable

Interface Box	Power Cord

Dongle Adapter Cable

19406

497-0424789 Release F

04/04

9 of 75

Image 9

Contents Information Products RSD-Atlanta RealScan Installation and Owner GuideContents Laser Safety Label Laser Module Label Laser Power Revision Record Obtaining Technical Assistance Obtaining Additional InformationNCR RealScan 7883 Mountings Step Installation InstructionsInstalling Power Supply and Interface Cables Connecting the Cables to an NCR RealScanStandard Interface Connection USB Interface Connection IBM HID NCR RealScan 7835/7836 Auxiliary RS-232 PortSpecial Installations RS-232 PeripheralsRealScan 7892 Bi-Modal Presentation Scanner Programming the RealScan RealScan 7832 ProgrammingRealScan 7837 Programming Factory Default RS232, 7 DATA, 1 STOP, Space Parity Setting Program Parameters and Verifying Host Connection Turning on the RealScanFlash Latest Firmware Programming the RealScan UPC/EAN Programming DefaultsBaud Rate Programming for USB Connection RS-232 CommunicationsIBM Communications RSS-14 Stacked Reduced Space SymbologyRSS Expanded RSS Expanded StackedMaking Other Program Changes Enabling RSSDisabling RSS UPC-A Scan Sample Tags01234 5 678 9 Determining Label QualityScan Zone Adjusting Screw Setting RealScan 7883 Scan ZoneVertical Pass-by Scanning Horizontal Pass-by ScanningVertical Presentation Scanning from Bottom Vertical Presentation Scanning from TopMounting the RealScan Rubber FeetPlastic Top Plate Plastic Top Plate ScannerC Latch Clip Mounting Screw Vertical Mounting Bracket Checkstand Cutout Checkpoint CableCable Clamps Operating the Scanner Cleaning the Scanner Green Status Tones Problem Indicator Correcting Scanner ProblemsThen supply again Interface Connector Interface InformationMost Common Interface Cables Communications Protocol Programming WorksheetCommunications Protocol Options 4 and B not supported yet Checkstand Hole RealScan 7883 Horizontal Mount FeaturesVentilation Requirements Checkstand Hole RealScan 7883 Flat MountInstallation Type Input Voltage L1, L2 Circuit Breakers Electrical WiringNCR Components NCR RealScan Mettler Toledo Scale, & Sensormatic ScanMaxTMHSSensormatic Components Mettler Toledo ComponentsSystem Construction Right-TO-Left ScanningLeft-To-Right Scanning Configuring the Scale Installing the Scanner Connecting Sensormatic Components Routing the Cables Completing the Installation Calibrating the Mettler Toledo Scale NCR RealScan 7883 Installation and Owner Guide Sensormatic Programmable Functions Sensormatic Deactivation IndicatorsTroubleshooting Scanner ProblemsScale Problems Sensormatic Deactivation Programming Worksheets Communications ProtocolGood Read Tone Bar Codes TimersCode Bar Codes Unique Identifier Label Identifiers21 RS-232 Parameters 20 RS-232 Parameters22 RS-232 Prefix Byte 23 RS-232 Terminator Byte24 RS-232 Communications Options Miscellaneous Parameters RealScan Ascii Code Chart Identification Labels Regulatory InformationNCR Corporation Duluth, Ga CE Mark ApplicabilityDeclaration of Conformity Laser Safety Laser Safety LabelLaser Module Label Laser Power Reset Volume AdjustmentDefault Programming TagsProgramming Mode Save and ResetEnd Diagnostic Mode RS-232 Temporary Service ModeAbort Mode Reset TalliesHex Firmware FlashingR0050 R0053 Hex a Hex B Hex CHex D Hex F Hex E