NCR 7883 manual System Construction, Right-TO-Left Scanning, Left-To-Right Scanning

Page 41

NCR RealScan 7883 Installation and Owner Guide

System Construction

The NCR RealScan 7883, METTLER TOLEDO® Scale, & ScanMaxTMHS system can be constructed for right-to-left scanning or for left-to-right scanning. This is accomplished through the orientation of the Bridge Plate within the scale unit.

Right-TO-Left Scanning

20208

Left-To-Right Scanning

20209

497-0424789 Release F

04/04

41 of 75

Image 41

Contents Information Products RSD-Atlanta RealScan Installation and Owner GuideContents Laser Safety Label Laser Module Label Laser Power Revision Record Obtaining Technical Assistance Obtaining Additional InformationNCR RealScan 7883 Mountings Step Installation InstructionsStandard Interface Connection Installing Power Supply and Interface CablesConnecting the Cables to an NCR RealScan USB Interface Connection IBM HID NCR RealScan 7835/7836 Auxiliary RS-232 PortRealScan 7892 Bi-Modal Presentation Scanner Special InstallationsRS-232 Peripherals RealScan 7837 Programming Programming the RealScanRealScan 7832 Programming Factory Default RS232, 7 DATA, 1 STOP, Space Parity Flash Latest Firmware Programming the RealScan Setting Program Parameters and Verifying Host ConnectionTurning on the RealScan UPC/EAN Programming DefaultsBaud Rate IBM Communications Programming for USB ConnectionRS-232 Communications RSS-14 Stacked Reduced Space SymbologyRSS Expanded RSS Expanded StackedDisabling RSS Making Other Program ChangesEnabling RSS UPC-A Scan Sample Tags01234 5 678 9 Determining Label QualityScan Zone Adjusting Screw Setting RealScan 7883 Scan ZoneVertical Pass-by Scanning Horizontal Pass-by ScanningVertical Presentation Scanning from Bottom Vertical Presentation Scanning from TopPlastic Top Plate Mounting the RealScanRubber Feet Plastic Top Plate ScannerC Latch Clip Mounting Screw Vertical Mounting Bracket Cable Clamps Checkstand CutoutCheckpoint Cable Operating the Scanner Cleaning the Scanner Green Status Tones Problem Indicator Correcting Scanner ProblemsThen supply again Most Common Interface Cables Interface ConnectorInterface Information Communications Protocol Options 4 and B not supported yet Communications ProtocolProgramming Worksheet Checkstand Hole RealScan 7883 Horizontal Mount FeaturesVentilation Requirements Checkstand Hole RealScan 7883 Flat Mount Installation Type Input Voltage L1, L2 Circuit Breakers Electrical WiringNCR Components NCR RealScan Mettler Toledo Scale, & Sensormatic ScanMaxTMHSSensormatic Components Mettler Toledo ComponentsLeft-To-Right Scanning System ConstructionRight-TO-Left Scanning Configuring the Scale Installing the Scanner Connecting Sensormatic Components Routing the Cables Completing the Installation Calibrating the Mettler Toledo Scale NCR RealScan 7883 Installation and Owner Guide Sensormatic Programmable Functions Sensormatic Deactivation IndicatorsScale Problems TroubleshootingScanner Problems Sensormatic Deactivation Good Read Tone Programming WorksheetsCommunications Protocol Bar Codes TimersCode Bar Codes Unique Identifier Label Identifiers21 RS-232 Parameters 20 RS-232 Parameters24 RS-232 Communications Options 22 RS-232 Prefix Byte23 RS-232 Terminator Byte Miscellaneous Parameters RealScan Ascii Code Chart Identification Labels Regulatory InformationNCR Corporation Duluth, Ga CE Mark ApplicabilityDeclaration of Conformity Laser Module Label Laser SafetyLaser Safety Label Laser Power Reset Volume AdjustmentDefault Programming TagsEnd Programming ModeSave and Reset Abort Diagnostic ModeRS-232 Temporary Service Mode Mode Reset TalliesHex Firmware FlashingR0050 R0053 Hex a Hex D Hex BHex C Hex F Hex E