NCR manual NCR RealScan 7883 Installation and Owner Guide

Page 48

NCR RealScan 7883 Installation and Owner Guide

5.Depress the Zero Scale button or scan the Reset Scale tag. Two short beeps per second start to sound.

6.Place 20 pounds (or 10kg) on the Top Plate.

7.Depress the Zero Scale button or scan the Reset Scale tag. One long beep per second starts to sound.

8.Remove the 20 pounds (or 10 kg) from the Top Plate.

9.Depress the Zero Scale button or scan the Reset Scale tag. All beeps stop.

10.Replace the Calibration Switch Cover Screw.

11.Scan the Reset Scale tag.

Note: If using the Reset tag, the scanner speaks (assuming speech is enabled) after completing reset. You must have Firmware above 497-0434118 to use Scale Reset tag for calibrating the scale; as noted above, it is recommended the scale display be used.

48 of 75

04/04

497-0424789 Release F

Image 48

Contents RealScan Installation and Owner Guide Information Products RSD-AtlantaContents Laser Safety Label Laser Module Label Laser Power Revision Record Obtaining Additional Information Obtaining Technical AssistanceNCR RealScan 7883 Mountings Installation Instructions StepInstalling Power Supply and Interface Cables Connecting the Cables to an NCR RealScanStandard Interface Connection USB Interface Connection IBM HID Auxiliary RS-232 Port NCR RealScan 7835/7836Special Installations RS-232 PeripheralsRealScan 7892 Bi-Modal Presentation Scanner Programming the RealScan RealScan 7832 ProgrammingRealScan 7837 Programming Factory Default RS232, 7 DATA, 1 STOP, Space Parity Setting Program Parameters and Verifying Host Connection Turning on the RealScanFlash Latest Firmware Programming the RealScan Programming Defaults UPC/EANBaud Rate Programming for USB Connection RS-232 CommunicationsIBM Communications Reduced Space Symbology RSS-14 StackedRSS Expanded RSS Expanded StackedMaking Other Program Changes Enabling RSSDisabling RSS Scan Sample Tags UPC-ADetermining Label Quality 01234 5 678 9Setting RealScan 7883 Scan Zone Scan Zone Adjusting ScrewHorizontal Pass-by Scanning Vertical Pass-by ScanningVertical Presentation Scanning from Top Vertical Presentation Scanning from BottomMounting the RealScan Rubber FeetPlastic Top Plate Plastic Top Plate ScannerC Latch Clip Mounting Screw Vertical Mounting Bracket Checkstand Cutout Checkpoint CableCable Clamps Operating the Scanner Cleaning the Scanner Correcting Scanner Problems Green Status Tones Problem IndicatorThen supply again Interface Connector Interface InformationMost Common Interface Cables Communications Protocol Programming WorksheetCommunications Protocol Options 4 and B not supported yet Features Checkstand Hole RealScan 7883 Horizontal MountCheckstand Hole RealScan 7883 Flat Mount Ventilation RequirementsElectrical Wiring Installation Type Input Voltage L1, L2 Circuit BreakersNCR RealScan Mettler Toledo Scale, & Sensormatic ScanMaxTMHS NCR ComponentsMettler Toledo Components Sensormatic ComponentsSystem Construction Right-TO-Left ScanningLeft-To-Right Scanning Configuring the Scale Installing the Scanner Connecting Sensormatic Components Routing the Cables Completing the Installation Calibrating the Mettler Toledo Scale NCR RealScan 7883 Installation and Owner Guide Sensormatic Deactivation Indicators Sensormatic Programmable FunctionsTroubleshooting Scanner ProblemsScale Problems Sensormatic Deactivation Programming Worksheets Communications ProtocolGood Read Tone Timers Bar CodesCode Bar Codes Label Identifiers Unique Identifier20 RS-232 Parameters 21 RS-232 Parameters22 RS-232 Prefix Byte 23 RS-232 Terminator Byte24 RS-232 Communications Options Miscellaneous Parameters RealScan Ascii Code Chart Regulatory Information Identification LabelsCE Mark Applicability NCR Corporation Duluth, GaDeclaration of Conformity Laser Safety Laser Safety LabelLaser Module Label Laser Power Volume Adjustment ResetDefault Programming TagsProgramming Mode Save and ResetEnd Diagnostic Mode RS-232 Temporary Service ModeAbort Reset Tallies ModeFirmware Flashing HexR0050 R0053 Hex a Hex B Hex CHex D Hex E Hex F