NCR 7883 manual Regulatory Information, Identification Labels

Page 61

NCR RealScan 7883 Installation and Owner Guide

Regulatory Information

Federal Communications Commission (FCC)

Radio Frequency Interference Statement

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user is required to correct the interference at his own expense.

Information to User: This equipment must be installed and used in strict accordance with the manufacturer’s instructions. However, there is no guarantee that interference to radio communications will not occur in a particular commercial installation. If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is encouraged to consult an NCR service representative immediately.

Caution: NCR is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by NCR. Such unauthorized modifications, substitutions, or attachments may void the user’s authority to operate the equipment. The correction of interference caused by such unauthorized modifications, substitutions, or attachments is the responsibility of the user.

Voluntary Control Council for Interference (VCCI)

Radio Frequency Interference Statement

16105

Canadian Department of Communications

Radio Frequency Interference Statement

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communication.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la Class A prescrites dans le Règlement sur le brouillage radioélectriques édicté par Ministère des Communications du Canada.

Identification Labels

The Identification Labels are molded into the bottom of the cabinet. They provide necessary information about the unit: power requirements, radio interference information, and applicable NCR patents.

497-0424789 Release F

04/04

61 of 75

Image 61
Contents Information Products RSD-Atlanta RealScan Installation and Owner GuideContents Laser Safety Label Laser Module Label Laser Power Revision Record Obtaining Technical Assistance Obtaining Additional InformationNCR RealScan 7883 Mountings Step Installation InstructionsConnecting the Cables to an NCR RealScan Installing Power Supply and Interface CablesStandard Interface Connection USB Interface Connection IBM HID NCR RealScan 7835/7836 Auxiliary RS-232 PortRS-232 Peripherals Special InstallationsRealScan 7892 Bi-Modal Presentation Scanner RealScan 7832 Programming Programming the RealScanRealScan 7837 Programming Factory Default RS232, 7 DATA, 1 STOP, Space Parity Turning on the RealScan Setting Program Parameters and Verifying Host ConnectionFlash Latest Firmware Programming the RealScan UPC/EAN Programming DefaultsBaud Rate RS-232 Communications Programming for USB ConnectionIBM Communications RSS-14 Stacked Reduced Space SymbologyRSS Expanded RSS Expanded StackedEnabling RSS Making Other Program ChangesDisabling RSS UPC-A Scan Sample Tags01234 5 678 9 Determining Label QualityScan Zone Adjusting Screw Setting RealScan 7883 Scan ZoneVertical Pass-by Scanning Horizontal Pass-by ScanningVertical Presentation Scanning from Bottom Vertical Presentation Scanning from TopRubber Feet Mounting the RealScanPlastic Top Plate Plastic Top Plate ScannerC Latch Clip Mounting Screw Vertical Mounting Bracket Checkpoint Cable Checkstand CutoutCable Clamps Operating the Scanner Cleaning the Scanner Green Status Tones Problem Indicator Correcting Scanner ProblemsThen supply again Interface Information Interface ConnectorMost Common Interface Cables Programming Worksheet Communications ProtocolCommunications Protocol Options 4 and B not supported yet Checkstand Hole RealScan 7883 Horizontal Mount FeaturesVentilation Requirements Checkstand Hole RealScan 7883 Flat MountInstallation Type Input Voltage L1, L2 Circuit Breakers Electrical WiringNCR Components NCR RealScan Mettler Toledo Scale, & Sensormatic ScanMaxTMHSSensormatic Components Mettler Toledo ComponentsRight-TO-Left Scanning System ConstructionLeft-To-Right Scanning Configuring the Scale Installing the Scanner Connecting Sensormatic Components Routing the Cables Completing the Installation Calibrating the Mettler Toledo Scale NCR RealScan 7883 Installation and Owner Guide Sensormatic Programmable Functions Sensormatic Deactivation IndicatorsScanner Problems TroubleshootingScale Problems Sensormatic Deactivation Communications Protocol Programming WorksheetsGood Read Tone Bar Codes TimersCode Bar Codes Unique Identifier Label Identifiers21 RS-232 Parameters 20 RS-232 Parameters23 RS-232 Terminator Byte 22 RS-232 Prefix Byte24 RS-232 Communications Options Miscellaneous Parameters RealScan Ascii Code Chart Identification Labels Regulatory InformationNCR Corporation Duluth, Ga CE Mark ApplicabilityDeclaration of Conformity Laser Safety Label Laser SafetyLaser Module Label Laser Power Reset Volume AdjustmentDefault Programming TagsSave and Reset Programming ModeEnd RS-232 Temporary Service Mode Diagnostic ModeAbort Mode Reset TalliesHex Firmware FlashingR0050 R0053 Hex a Hex C Hex BHex D Hex F Hex E