NCR 7883 manual Revision Record

Page 4

NCR RealScan 7883 Installation and Owner Guide

Hex E	75
Hex F	75

Revision Record

Date	Pages	Issue	Remarks
02-02	All	A	First printing.
07-02	All	B	Updated to match latest units.
09-02	All	C	Added USB Interface.
			Updated to match latest units.
10-02	59-72	D	Added Programming Tags.
09-03	All	E	Added 7883-1200 information.
			Updated to match latest units.
04-04	All	F	Updated Auxiliary Port and USB
			Programming information

4 of 75

04/04

497-0424789 Release F

Image 4

Contents RealScan Installation and Owner Guide Information Products RSD-AtlantaContents Laser Safety Label Laser Module Label Laser Power Revision Record Obtaining Additional Information Obtaining Technical AssistanceNCR RealScan 7883 Mountings Installation Instructions StepConnecting the Cables to an NCR RealScan Installing Power Supply and Interface CablesStandard Interface Connection USB Interface Connection IBM HID Auxiliary RS-232 Port NCR RealScan 7835/7836RS-232 Peripherals Special InstallationsRealScan 7892 Bi-Modal Presentation Scanner RealScan 7832 Programming Programming the RealScanRealScan 7837 Programming Factory Default RS232, 7 DATA, 1 STOP, Space Parity Turning on the RealScan Setting Program Parameters and Verifying Host ConnectionFlash Latest Firmware Programming the RealScan Programming Defaults UPC/EANBaud Rate RS-232 Communications Programming for USB ConnectionIBM Communications Reduced Space Symbology RSS-14 StackedRSS Expanded RSS Expanded StackedEnabling RSS Making Other Program ChangesDisabling RSS Scan Sample Tags UPC-ADetermining Label Quality 01234 5 678 9Setting RealScan 7883 Scan Zone Scan Zone Adjusting ScrewHorizontal Pass-by Scanning Vertical Pass-by ScanningVertical Presentation Scanning from Top Vertical Presentation Scanning from BottomRubber Feet Mounting the RealScanPlastic Top Plate Plastic Top Plate ScannerC Latch Clip Mounting Screw Vertical Mounting Bracket Checkpoint Cable Checkstand CutoutCable Clamps Operating the Scanner Cleaning the Scanner Correcting Scanner Problems Green Status Tones Problem IndicatorThen supply again Interface Information Interface ConnectorMost Common Interface Cables Programming Worksheet Communications ProtocolCommunications Protocol Options 4 and B not supported yet Features Checkstand Hole RealScan 7883 Horizontal MountCheckstand Hole RealScan 7883 Flat Mount Ventilation RequirementsElectrical Wiring Installation Type Input Voltage L1, L2 Circuit BreakersNCR RealScan Mettler Toledo Scale, & Sensormatic ScanMaxTMHS NCR ComponentsMettler Toledo Components Sensormatic ComponentsRight-TO-Left Scanning System ConstructionLeft-To-Right Scanning Configuring the Scale Installing the Scanner Connecting Sensormatic Components Routing the Cables Completing the Installation Calibrating the Mettler Toledo Scale NCR RealScan 7883 Installation and Owner Guide Sensormatic Deactivation Indicators Sensormatic Programmable FunctionsScanner Problems TroubleshootingScale Problems Sensormatic Deactivation Communications Protocol Programming WorksheetsGood Read Tone Timers Bar CodesCode Bar Codes Label Identifiers Unique Identifier20 RS-232 Parameters 21 RS-232 Parameters23 RS-232 Terminator Byte 22 RS-232 Prefix Byte24 RS-232 Communications Options Miscellaneous Parameters RealScan Ascii Code Chart Regulatory Information Identification LabelsCE Mark Applicability NCR Corporation Duluth, GaDeclaration of Conformity Laser Safety Label Laser SafetyLaser Module Label Laser Power Volume Adjustment ResetDefault Programming TagsSave and Reset Programming ModeEnd RS-232 Temporary Service Mode Diagnostic ModeAbort Reset Tallies ModeFirmware Flashing HexR0050 R0053 Hex a Hex C Hex BHex D Hex E Hex F