JAI Shutter Speed Control Dial TM-1400 only, Shutter Exposure Time Seconds, Normal Async

Page 16

2.2.3Shutter Speed Control Dial (TM-1400 only)

Shutter speed can be selected by switching the shutter dial to the appropriate setting (0 through 9). The factory default settings correspond to the shutter speeds as shown in below.

TABLE 5. Shutter Speed Control Dial

	Shutter Exposure Time (Seconds)

	Normal	Async

0	no shutter (1/30)	no shutter (1/30)

1	1/60	1/16,000

2	1/125	1/8,000

3	1/250	1/4,000

4	1/500	1/2,000

5	1/1,000	1/1,000

6	1/2,000	1/500

7	1/4,000	1/250

8	1/8,000	1/125

9	1/16,000	Ext. pulse width control

Page 9

Installation

9	0	1
8		2
7		3
6	5	4
	5

2.2.4RS-232 Communication Cable (TM-1400 only)

FIGURE 5. Serial Communication Cable RS-232B-12

2000±20mm

40±3mm 1925±10mm

Receptacle

75mm±5mm 190±5mm

1 6

5 9

Jack

The RS-232 controller set CS-232E includes cable RS-232B-12 interface cable, software disk, and a quick-start card. The TM-1400 camera’s built-in look-up table (LUT) can be controlled by an external RS-232 interface. The camera settings can be programmed or changed using the communication cable and software. Commands from the RS-232 interface will override the rear panel switch settings of the camera. Please refer to the AccuPiXEL Series Camera-Control Software manual for details on the graphical user interface.

TM-1400 Series Progressive Scan Shutter Cameras

Image 16

Contents TM-1400 Series Progressive Scan Shutter Cameras CE Compliance JAI PULNiX, IncPage Installation Table of ContentsTroubleshooting TM-1400 System Configuration List of FiguresList of Tables Product Description May 2Features IntroductionFunctional Options WarrantyIntegration System Configuration TM-1400 System ConfigurationCamera Setup Getting StartedConnector Pin Configurations Pin DescriptionPin # Description LDVSerToFG Differential Serial Communication to frame grabber Installation 4 RS-232 Communication Cable TM-1400 only Shutter Speed Control Dial TM-1400 onlyShutter Exposure Time Seconds Normal AsyncInstallation Digital Output Cable TM-1400 only Pinout Configuration for Digital Output CableInstallation Camera Link Cable CL Versions Only Power Supplies and Power Cable Setup02S Interface Cable optional Installation Attaching the Analog Video Output Attaching the Camera LensCamera Rear Panel TM-1400 Mode Selection Switch Camera Rear Panel CL Versions Power and External Sync ConnectorProgressive Scanning Electronic Shutter Asynchronous ResetExternal Vinit With Pulse Width No-Delay Shutter Internal Shutter Speed ControlDynamic Range Control Programmable Look-Up Table LUT and Knee ControlScan Modes External SyncBayer Color Filter Color Versions Full Progressive ScanOperation Color Filter Array Bayer Color Filter Array CFAOperation Starting Pixel Configuration Sync and DataCamera Functions FDVColor Interpolation Operation Interpolation SoftwareManufacturer Frame Grabber Software Camera Timing Charts Tcc =14 nsec, Tdc = 6 nsec, Thd = 5 nsec Horizontal SignalsAsync Shutter Reset Timing Operation Mode 15 Frame /sec Async Shutter Reset Timing Async Shutter Reset Timing Partial Scan 500 Lines Async Shutter Reset Timing Partial Scan 250 Lines Serial Communication Kit CS-232C not required for CL version Problems and Solutions TroubleshootingSymptom No Video Symptom Dark VideoInformation and Support Resources Appendix SpecificationsModel TM-1400 series Physical Dimensions Effective Image AreaPhysical Dimensions TM-1400CL Spectral ResponseW . j a i p u l n i x . c o m