Dell BMX01 owner manual Dell PowerConnect M8024 10 Gb Ethernet switch I/O module

Page 98

Environmental

Expanded Operating Temperature Restrictions

Storage Temperature

NOTE: Outside the standard operating temperature

(10 °C to 35 °C), the system can operate down to –5 °C or up to 45 °C for a maximum of 1% of its annual operating hours.

For temperatures between 40 °C and 45 °C, de-rate maximum allowable dry bulb temperature by 1 °C per 125 m above 950 m (1 °F per 228 ft).

Install blades that fulfill the requirements for expanded operating temperature range.

NOTE: For more information on the blade-specific restrictions for the expanded operating temperature range, see the technical specifications in the blade's Owner's Manual at support.dell.com/manuals.

Only 2700 W power supplies are supported.

Install fans of the following ratings:

12 V, 5.0 A

12 V, 6.30 A

Only the following I/O modules are supported:

Brocade M5424 FC8 I/O module

Dell M8428-k 10 Gb converged network switch

Cisco 1 GE 3130X-s switch

Mellanox M3601Q DDR/QDR switch

Dell PowerConnect M8024-k switch

Dell PowerConnect M6220 Ethernet switch I/O module

Dell PowerConnect M8024 10 Gb Ethernet switch I/O module

–40 °C to 65 °C (–40 °F to 149 °F) with a maximum temperature gradation of 20 °C per hour.

98

Image 98
Contents Regulatory Model BMX01 Page Contents Configuring The I/O Modules Installing Enclosure Components Getting Help Troubleshooting The EnclosureTechnical Specifications About Your System System OverviewBlade Numbering Full Height Blades System Control-Panel Features Blade Numbering Quarter Height BladesLCD Module LCD Module Features LCD DisplayCenter button Configuration WizardUsing The LCD Module Menus Back-Panel Features Back-Panel FeaturesPower Supply Indicators Back-Panel Module Bay NumberingPower to the system Fan Module IndicatorsIndicator Description Power supply fault Icon IndicatorAvocent iKVM Analog Switch Module Optional Solid GreenAvocent Analog iKVM Switch Module Features And Indicators CMC Module Features CMC ModuleCMC network cable CMC Fail-Safe ModeCondition Description CMC removal Daisy-Chain CMC Network Connection System Messages Other Information You May NeedPage Before You Begin Initial Setup SequenceInitial CMC Network Configuration Configuring The CMC Using The LCD Configuration Wizard Configuring The CMC Using a Management Station And CLIHttps//CMC IP addressport number Logging In To The CMC Using The Web-Based InterfaceHttps//CMC IP address Adding And Managing CMC Users Configuring iDRAC Networking Using The Web-Based InterfaceClick Setup → Deploy Installing Or Updating The CMC Firmware Setting The First Boot Device For ServersConfiguring And Managing Power Downloading The CMC Firmware Updating The CMC Firmware Using The Web-Based InterfaceUpdating The CMC Firmware Using Racadm Tiering The Avocent iKVM Switch From An Analog KVM Switch Configuring The Optional iKVM Switch ModuleTiering The Avocent iKVM Switch From a Digital KVM Switch Updating The iKVM FirmwareConfiguring The Analog Switch Click Setup → Devices → Device ModifyViewing And Selecting Servers FlexAddress FlexAddress PlusConnectivity General I/O Module Configuration GuidelinesNetwork Information Fabric aFabric B Fabric CFull-Height Blades PowerEdge M610x OnlyMezzanine Cards Half-Height BladesSupported I/O Module Configurations Standard LOM Dual-Port Mapping Module Port Mapping-Full-Height BladesQuarter-Height Blades Dual-Port Mezzanine CardsBlade Module Mezzanine Card C Port Mezzanine Card B Blade Module Blade Module Mezz1FabC Port Mezz2FabBMezz3FabC Port Mezz4FabB Blade Module Quad-Port Mezzanine Cards +8Port4 Module Port MappingHalf-Height BladesMezzFABCBlade n Example of I/O Module Port Assignments Half-Height Blade Blade n Integrated LOM1 Port n Integrated LOM2Module Port Mapping-Quarter-Height Blades Blade n ModuleDual-Port Mezzanine Cards Sleeve Module Sleeve Module Quad-Port Mezzanine Cards Modules-Switches Mellanox M4001F/M4001Q Infiniband Switch I/O ModuleDell PowerConnect KR 8024-k Switch Mellanox M4001F/M4001Q Infiniband Switch ModuleDell PowerConnect M8428-k 10 Gb Converged Network Switch Dell PowerConnect KR 8024-k SwitchMellanox M2401G DDR Infiniband Switch I/O Module Dell PowerConnect M8428-k 10 Gb Converged Network SwitchMellanox M3601Q QDR Infiniband Switch I/O Module Mellanox M2401G DDR Infiniband Switch ModuleCisco Catalyst Ethernet Switch I/O Modules Mellanox M3601Q QDR Infiniband Switch I/O ModuleDell PowerConnect M6348 1 Gb Ethernet Switch I/O Module Cisco Catalyst Ethernet Switch Module FeaturesDell PowerConnect M6220 Ethernet Switch I/O Module PowerConnect M6348 1 Gb Ethernet Switch I/O Module FeaturesDell PowerConnect M8024 10 Gb Ethernet Switch I/O Module PowerConnect M6220 Ethernet Switch I/O ModulePowerConnect M8024 10 Gb Ethernet Switch I/O Module Dell 8/4 Gbps FC SAN ModuleModules-Pass-Through Dell 4 Gbps Fibre Channel Pass-Through ModuleStatus/Identification Indicator InstalledDell 10 GbE KR Pass-Through I/O Module Dell 10 GbE KR Pass-Through I/O ModuleDell 10 Gb Ethernet Pass-Through Module 10/100/1000 Mb Ethernet Pass-Through I/O ModuleBrocade M4424 SAN I/O Module 100/1000 Mb Ethernet Pass-Through I/O ModuleBrocade M4424 SAN I/O Module Brocade M5424 FC8 I/O Module Brocade M5424 FC8 I/O Module Module power indicator Page Removing a Blade Removing And Installing a BladeRecommended Tools Blade handle Removing The Sleeve Removing And Installing a SleeveInstalling a Blade Power Supply Modules Installing The SleevePower Supply Blanks Removing a Power Supply ModulePower Cable Retention Clip Installing a Power Supply Module Fan ModulesInstalling a Fan Module Removing a Fan ModuleInstalling a CMC Module Removing a CMC ModuleClick the Power Management tab Select the Reset CMC warm boot buttonRemoving An iKVM Module Installing An iKVM ModuleIKVM Module Modules Removing An I/O ModuleRemoving The Enclosure Bezel Installing An I/O ModuleEnclosure Bezel Enclosure Midplane Installing The Enclosure BezelRemoving The Front Module Cage Assembly And Midplane Front module cage assembly Enclosure Torx T20 screws Installing The Midplane And Front Module Cage Assembly Removing and Installing the MidplaneEnclosure Control Panel Assembly Removing The Control PanelInstalling The Control Panel Removing The LCD ModuleInstalling The LCD Module Removing and Installing the LCD ModulePage Troubleshooting The Enclosure Troubleshooting Enclosure ComponentsTroubleshooting a Wet Enclosure Troubleshooting Power Supply ModulesTroubleshooting I/O Modules Troubleshooting Fan ModulesTroubleshooting The iKVM Module Page Optional Avocent iKVM Module Enclosure SpecificationsPower Supply Module Chassis Management Controller ModuleBrocade FC8 Fibre Channel Switch Module Module SpecificationsPowerConnect M6220 Ethernet Switch Module Brocade FC4 Fibre Channel Switch ModuleGb Ethernet Pass-Through Module Mellanox M4001F/M4001Q Infiniband Switch I/O ModuleMellanox Infiniband Switch Module Fibre Channel Pass-Through ModuleDell PowerConnect M8024 10 Gb Ethernet switch I/O module Contacting Dell Visit support.dell.com