Dell S100, S300 manual Swapping Two Virtual Disks, Before You Begin

Page 55

Swapping Two Virtual Disks

Use the Swap Two Virtual Disks option of the PERC Virtual Disk Management utility to arrange virtual disks in a different order.

CAUTION: Do not swap the first-listed virtual disk at Virtual Disks if it is the system’s bootable virtual disk. The bootable virtual disk must always be the first- listed virtual disk at Virtual Disks.

Before You Begin

•The Swap Two Virtual Disks option is enabled only if there is at least one initialized physical disk in the system. For example, if all the physical disks in the system are Non-Raid, the Swap Two Virtual Disks option is disabled.

•It is recommended that the bootable virtual disk be a redundant virtual disk-type, such as RAID 1, RAID 5, or RAID 10, to preserve data in case a physical disk in the virtual disk fails. As required, swap that virtual disk into the first position at Virtual Disks, if it is not already virtual disk 1. See the Swap Two Virtual Disks option below.

•The boot device and the boot order are user-selectable.

•The swap feature is available only with the PERC Virtual Disk Management utility.

NOTE: Only two virtual disks can be swapped at a time.

1Power-up the system to start booting.

2When prompted, press the <Ctrl><R> keys to access the PERC Virtual Disk Management utility.

3At the Main Menu field, select Swap Two Virtual Disks. Press <Enter>.

4Use the arrow keys to highlight a virtual disk at the Virtual Disk field. Press <Insert>.

5Use the arrow keys to highlight another virtual disk. Press <Insert>.

6Press <Enter> to swap the virtual disks.

RAID Configuration and Management

55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents User’s Guide February Contents Physical Disk-Related Errors Installing the Perc S300 AdapterComplete the Hardware Installation Installing the Microsoft Windows DriversIndustry Canada Notice Canada Only RAID Technology Understanding Disk ArraysContents Page Safety When Working Inside Your System Safety GeneralProtecting Against Electrostatic Discharge Page Introduction OverviewOverview Supported Platforms Physical disks RequirementsOverview Boot to it Summary of RAID Levels About RAIDDisk Striping RAID TerminologyDisk Mirroring Parity Data Spanned RAID LevelsExample of Distributed Parity RAID General Features FeaturesDescription Description Allows hot-swapping Physical disks, in the same virtual disk That supports hot-swapping DisksBackplane with hot-swap capability Features Migration during an OCE Virtual diskSpecifications RAID Before You Begin Hardware InstallationGeneral Considerations Installing the Perc S300 Adapter Installing a Perc S300 Adapter Connecting the Cables Connect Physical Disks to the Perc S300 Adapter Complete the Hardware InstallationHardware Installation Installing the Microsoft Windows Drivers Installing the DriversDownloading the Controller Driver Media Operating System And Device Driver Media Pre-Installation Requirements for the Controller DriversTo Use Sata Controller to either ATA Mode or Ahci Pre-Installation Procedures For The Controller Drivers Steps DVD, and so on, perform the following For Microsoft Windows Server 2008 and Windows Server 2008 R2 For Microsoft Windows Server For Microsoft Windows Server 2008 and Windows Server 2008 R2 Installing the Drivers Installing the Drivers Perc Virtual Disk Management Utility Operations Description RAID Configuration ManagementAccessing the Perc Virtual Disk Management Utility Perc Virtual Disk Management Text Colors Description Initializing Physical Disks Before You Begin Creating Virtual DisksRAID Configuration and Management Deleting Virtual Disks RAID Configuration and Management Swapping Two Virtual Disks Create a Global Hot Spare Managing Global Hot SparesDelete a Global Hot Spare Viewing Virtual Disk Details Viewing Physical Disk DetailsRescanning Disks Controller Options Description How to OperateController Options Pause if Degraded Continuing to BootRAID Configuration and Management System Startup Problems TroubleshootingRAID Mode to ATA Mode Boot Mode, Boot Sequence Bios Bios Screen Corrective Action Lost This warning message appears when multiple virtual disks are This warning message appears when From virtual disk creation Virtual Disk-Related Errors A Virtual Disk is in a Failed State On the virtual diskRedundant virtual disk 12. Cannot Create a Global Hot Spare Select View Virtual Disk Details 14. a Dedicated Hot Spare Fails Physical Disk-Related ErrorsTroubleshooting S300 adapter Controller SpecificationsAppendix a Read, Write, and Cache PolicyPerc S300 adapter Controller TasksPhysical Disk Tasks Table A-3. Physical Disk Tasks Physical Disk Task NameAdapter Virtual Disk TasksSupported RAID Levels Table A-4. Virtual Disk Tasks Virtual Disk Task NameVirtual Disk Specifications RAID Technology Understanding Disk Arrays and Virtual Disks Appendix BUnderstanding RAID Levels Appendix B Table B-2. Physical Disk States Definition Disk States Virtual and Physical DisksTable B-3. Virtual Disk States State Definition Failure StatesPhysical Disk States Table B-5. Minimum and Maximum Physical Disk ConfigurationsCreating Virtual Disks Future Expansion Understanding Physical DisksRescanning Physical Disks for Changes in State Dedicated Hot SparesGlobal Hot Spares Regulatory Notices Appendix CFCC, Class a FCC Notice U.S. OnlyFCC, Class B Industry Canada, Class B Industry Canada Notice Canada OnlyCE Notice European Union Industry Canada, Class aAppendix C CE Mark Notice Contacting Dell Appendix DAppendix D Index Index Index 100 101 102 103 Glossary104 105 106 Acronym for nanoseconds, one billionth of a second 107108 109 110
Related manuals
Manual 81 pages 24.45 Kb Manual 81 pages 29.77 Kb
Top Page Image Contents