Dell 6100, 200 manual Dell Confidential Preliminary 12/17/96

Page 19

Tables

Table 2-1. Boot Routine Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Table 3-1. System Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Table 3-2. System Beep Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Table 3-3. SCSI Hard-Disk Drive Indicator Patterns. . . . . . . . . . . . . . . . . . . . . . 3-6

Table 4-1. Default IRQ Line Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Table 5-1. Option Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Table 5-2. System Diagnostics Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8

Table 7-1. Power Cable Connectors on the Power-Supply Paralleling Board . . 7-10

Table 8-1. Sample SIMM Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6

Table 8-2. Valid Microprocessor Configurations . . . . . . . . . . . . . . . . . . . . . . . 8-10

Table 11-1. Help Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2

Table 11-2. International Dialing Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6

Table 11-3. Dell Contact Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-8

Table B-1. Color Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-3

Table C-1. System-Board Jumper and Switch Settings . . . . . . . . . . . . . . . . . . . .C-3

Table C-2. System Board Connectors and Sockets . . . . . . . . . . . . . . . . . . . . . . .C-5

Table C-3. Microprocessor Module Jumper Settings . . . . . . . . . . . . . . . . . . . . . .C-7

Table C-4. SCSI Backplane Board Connectors . . . . . . . . . . . . . . . . . . . . . . . . . .C-8

Table C-5. Power Supply Paralleling Board Connectors . . . . . . . . . . . . . . . . . .C-10

DELL CONFIDENTIAL Preliminary 12/17/96

xxiii

Image 19
Contents 167$//$7,21$17528%/6+227,1**8 Page When Working Inside the Computer Safety InstructionsProtecting Against Electrostatic Discharge When Using the Computer System About This Guide PrefaceNotational Conventions Other Documentation You May NeedExamples autoexec.bat and c\windows Typographical ConventionsPage Contents Chapter Running the System Diagnostics Chapter Checking the Equipment Chapter Installing System Board Options Chapter Installing Drives in the External Bays Before You Call Figures Figure B-1 Column x 25-Line Character Set Subtest Screen Tables Page Dell Confidential Preliminary 12/17/96 Xxiv Is the computer wet or damaged? Checking the BasicsBacking Up Files Basic ChecksRun the system diagnostics as described in Chap- ter Checking Connections and SwitchesBack Panel Features Is the monitor operating properly? Yes. Continue to step Turn on the systemIs the mouse or printer operating properly? Boot Routine IndicationsLook and Listen Is the keyboard operating properly? Yes. Continue to stepSystem Configuration Utility System Setup ProgramSystem Messages Messages and CodesSystem Messages CodeMessage System Messages System Beep Codes System Beep CodesAlert Log Messages From the Dell HIP Program Diagnostics MessagesScsi Hard-Disk Drive Indicator Codes Scsi Hard-Disk Drive Indicator PatternsPage Error Messages Finding Software SolutionsInstalling and Configuring Software Using SoftwareAvoiding Interrupt Assignment Conflicts Input ErrorsDefault IRQ Line Assignments Program ConflictsFeatures of the System Diagnostics Running the System DiagnosticsWhen to Use the System Diagnostics Sample Diagnostics Menu Starting the System DiagnosticsSample System Diagnostics Main Screen How to Use the System DiagnosticsSelect How to Use the MenuMain Menu Categories RunRun Under Subtest SubtestOption Parameters OptionsAbout Test LimitsKey-Help System Diagnostics Tests Tests in the System DiagnosticsQuit System Diagnostics Tests System Set Test Group Error MessagesWhy Run a RAM Test? RAM Test GroupWhy Run a System Set Test? Video Test Group Why Run a Video Test?Keyboard Test Group Why Run a Keyboard Test?Mouse Test Serial/Infrared Ports Test Group Why Run the Mouse Test?Why Run a Diskette Drives Test? Diskette Drives Test GroupParallel Ports Test Group Why Run a Serial/Infrared Ports Test?Scsi Devices Test Group Why Run a Parallel Ports Test?Why Run a Scsi Devices Test? Page Run the system diagnostics software Troubleshooting the MonitorChecking the Equipment Troubleshooting I/O Ports Troubleshooting the KeyboardCheck the contents of the start-up files Troubleshooting the Basic I/O FunctionsChange the necessary statements in the start-up files Attempt another print operation on the parallel printer Troubleshooting a Parallel PrinterTroubleshooting a Serial I/O Device Run the parallel printer’s self-testChecking Inside the Computer Safety First- For You and the ComputerRemoving the Computer Covers Removing and Replacing the Computer CoversRemoving the Computer Covers Replacing the Computer CoversInside the Chassis Removing the Front BezelRemove the computer covers Inside the Chassis-Front/Left Side View Responding to a Dell HIP Alert Message Troubleshooting a Wet ComputerVerify all internal cable and component connections Troubleshooting a Damaged ComputerLet the computer dry for at least 24 hours Check all the board and card connections in the computerTroubleshooting the RTC Chip Replacing a Power Supply Troubleshooting Power Supply ProblemsCheck the cable connections listed in Table Troubleshooting a Cooling FanTroubleshooting Power Cable Connections Power Cable Connectors on Power-Supply Paralleling BoardReplacing a Cooling Fan Reinstall the fan carrier in the computerReplace the left computer cover Reseat the expansion cards in their connectors Troubleshooting Expansion CardsTurn on the system, including any attached peripherals Troubleshooting System MemoryCorrect the system board’s configuration jumper settings Run the RAM Test Group in the system diagnosticsTroubleshooting the Video Subsystem Determine whether a video expansion card is installed Troubleshooting the System BoardRemove the video expansion card, and repeat step Disconnect the keyboard and reboot the system Troubleshooting the Diskette Drive SubsystemRepeat steps 1 and 2, and remove all expansion cards Troubleshooting the Diskette Drive Sub- systemChecking the Diskette Drive Subsystem Check the diskette drive cablingTroubleshooting a Scsi Tape Drive Drive Indicator Error Codes Troubleshooting Scsi Hard-Disk DrivesRemove the drive carrier and install it in another drive bay Troubleshooting the Scsi Hard-Disk DriveChecking Inside the Computer Page Installing System Board Options Installing System Board OptionsExpansion Cards System Board FeaturesExpansion Cards Installing an Expansion CardConnect any cables that should be attached to the card Relocating or Removing an Expansion CardSimm Installation Guidelines Memory Upgrade KitsAdding Memory Sample Simm Configurations Shows the location of the Simm sockets on the memory module Performing a Memory UpgradeInstalling SIMMs Removing SIMMs Valid Microprocessor Configurations Remove the left computer cover Remove the heat sink Remove the appropriate modulesRemove the microprocessor from the socket Unpack the new microprocessor Install the microprocessor in the socket see Fig- ureReplace the microprocessor securing clip Replacing the RTC Chip13. RTC Chip Install the new RTC chipPage Installing Drives in the External Bays Installing Drives in the External BaysExternal Drive Bay Hardware Before You BeginRemoving and Replacing Front-Panel Inserts Connecting the DriveDC Power Cables Installing Scsi Devices in the External BaysScsi Configuration Information Prepare the drive for installation Installing a Scsi DeviceRemove the computer covers and front bezel Page Configure the controller card if necessary Remove both computer covers and the front bezel Prepare the tape drive and controller card for installationInstalling Drives in the Internal Bays 10-1 Installing Drives in the Internal BaysInternal Drive Hardware Scsi Hard-Disk Drive ConfigurationInstall any required Scsi device drivers Removing and Installing a Scsi Hard-Disk DriveRemove the hard-disk drive Scsi Hard-Disk Drive Indicator PatternsInstalling Drives in the Internal Bays 10-5 Partitioning and Formatting Scsi Hard-Disk Drives Configuring the Boot DeviceHelp Tools Run the diagnostics for your Dell systemGetting Help Technical AssistanceWorld Wide Web on the Internet System DocumentationHelp Tools TechFax Service Commercial Online ServicesDell Diagnostics Program AutoTech ServiceTechConnect BBS Problems With Your OrderTechnical Support Service Product InformationBefore You Call Returning Items for Warranty Repair or CreditDell Contact Numbers International Dialing Codes 1344Getting Help 11-7 Belgium Dell Contact NumbersAustralia AustriaChina CanadaCzech Republic Germany DenmarkFinland FranceKorea IrelandItaly JapanMexico LuxembourgMacau MalaysiaSingapore New ZealandNorway PolandSwitzerland SwedenTaiwan Austin, Texas AutoTech Automated technical support Page Diagnostics Checklist Diagnostics Checklist Video Hardware Test Diagnostic Video TestsText Mode Character Test Video Memory TestCharacter Set Subtest 40 x Character Attributes Subtest 80 xCharacter Set Subtest 80 x Character Attributes Subtest 40 xColor Attributes Subtest 80 x Text Mode Color TestTable B-1. Color Attributes Graphics Mode Test Text Mode Pages Test640 x 480 2-Color Graphics Mode Screen 320 x 200 16-Color Graphics Mode Screen640 x 200 16-Color Graphics Mode Screen 640 x 350 16-Color Graphics Mode ScreenColor Palettes Test Solid Colors Test Page Jumpers Jumpers, Switches, and ConnectorsJumpers and Switches General Explanation SwitchesSystem Board Figure C-1. System Board Jumpers and SwitchesClear Cmos Clear Password Reserved Bios Recovery Table C-1. System-Board Jumper and Switch SettingsVideo Sleep System Board Labels Table C-2. System Board Connectors and SocketsFigure C-2. Microprocessor Module Jumpers Microprocessor ModuleTable C-3. Microprocessor Module Jumper Settings Scsi Backplane Board Table C-4. Scsi Backplane Board ConnectorsFigure C-4. Power-Supply Paralleling Board Power-Supply Paralleling BoardTable C-5. Power-Supply Paralleling Board Connectors Disabling a Forgotten PasswordDer Telekommunikation Abbreviations and AcronymsDram LIF Verband Deutscher Elektro Index Page Index Page Index Page Switches settings table, C-3 Page Index
Related manuals
Manual 132 pages 53.29 Kb Manual 6 pages 26.32 Kb Manual 214 pages 18.44 Kb Manual 82 pages 39.19 Kb