Compex Technologies NetPassage 15B manual Procedure for resetting password to default

Page 54

Appendix C Troubleshooting

JP6

JP5

JP4

Procedure for resetting password to default:

1.Switch OFF NetPassage 15B.

2.Remove jumper JP5.

3.Switch ON the router. The DIAG led will light up for a few seconds and off.

4.Switch OFF the router again and put back the jumper.

5.The password for the router will then be reset. To confirm this has been done, switch ON the router and log on to the Remote Access Router Manager again.

(Refer to Section 2.3, “Connecting to the Configuration Interface”)

Procedure for resetting to factory default:

1.Switch OFF the NetPassage 15B.

2.Remove jumper JP6.

3.Switch ON the router. The DIAG led will light up for a few seconds and off.

4.Switch OFF the router again and put back jumper.

5.The router configuration will then be reset. To confirm this has been done, switch ON the

router and log on to the Remote Access Router Manager again. (Refer to Section 2.3, “Connecting to the Configuration Interface”)

47

Image 54

Contents Page Trademark Information DisclaimerYour Feedback FCC Notice Declaration of ConformityTechnical Support Information Compex, IncReadyLINK Networktechnology GmbH About this Document ConventionsTable of Contents NetPassage 15B’s System Tools Introduction Key FeaturesProduct Overview Broadband Internet SharingWeb-based Configuration Interface Integrated 4-port 10/100Mbps SwitchTime-based Access Management Parallel BroadbandPackage Contents Panel Views & Descriptions Panel ViewsIndex Indicator Description Panel DescriptionTechnical Data NetPassage 15B SpecificationsHardware Setup Getting StartedTCP/IP Configuration of the Computers 192.168.168.1For Microsoft Windows 95/98/ME For Microsoft Windows 2000/XP 192.168.168.X Configuring your Computer with Static IP AddressNetmask 255.255.255.0 Subnet Mask 255.255.255.0 Gateway 192.168.168.1 DNS ServerSubnet Mask of 192.168.168.X and 255.255.255.0 respectively DNS Configuration Window Connecting to the Configuration Interface \WINDOWS\PINGCommand Menu Proxy SettingsConnecting to Web-based Configuration Interface Configuration WindowTelnet Command Console Connecting to NetPassage 15B’s Command Console via Telnet\WINDOWS\TELNET Command Console Login Configuring IP Addressing Configuring NetPassage 15BSetting up your LAN IP AddressAdvanced Option for Dhcp Server To reserve IP addresses for specific computersTo view the IP released by the Dhcp Server 4 titled Singapore Singtel Magix SuperSurf 5 titled Australia Big Pond Cable InternetCable Internet with Dynamic IP Assignment Cloning MAC Address to NetPassage 15B Cable Internet with Static IP Assignment Static IP Configuration Idle Timeout PasswordService Name UsernameUse non-standard Pppoe Singapore SingTel Magix SuperSurfReconnect Time Factor Ethernet typeNetwork Address Translator NAT Australia Big Pond Cable InternetIntroduction to Virtual Servers Virtual Server based on Port ForwardingVirtual Server based on IP Forwarding Defining Virtual Server based on De-Militarized Zone DMZDefining Virtual Server based on Port Forwarding Defining Virtual Server based on IP Forwarding Defining De- Militarized Zone Configuring Routing Protocol Static Routing Dynamic RoutingIP Packet Filtering Internet Application Filtering Managing NetPassage 15B from the Internet Activating Remote Router ManagementSelect Single from the drop down menu Http Port Telnet PortImplementing Parallel Broadband Setting Router Identity NetPassage 15B’s System ToolsSynchronizing Router’s Clock with your Computer Upgrading Router’s Firmware Profile Saving, Restore & Reset to Defaults Rebooting NetPassage 15BChanging Administrative Password Appendix a Console Commands Delete CommandDisconnect Command Enable CommandDisable Command Edit CommandSingapore Pacific Internet Broadband Appendix B ISP-Specific NotesSingapore SingNet Broadband Germany T-DSL & T-OnlineAppendix C Frequently Asked Questions Action Normal Reset Password to Reset to factoryProcedure for resetting password to default