Citizen CMP-10 manual Power Related Specifications, Battery

Page 73

8.POWER RELATED SPECIFICATIONS

8.1Battery

(1)	Battery type	Lithium-ion battery pack
(2)	Maximum capacity	2000 mAh
(3)	Number of sells	2
(4)	Maximum output voltage	4.2V/Cell
(5)	Cut-off voltage	2.75V/Cell
(6)	Standard charge	1000 mA, 23ºC, 4.2V/Cell, 3 hours charge
(7)	Initial capacity	1950 mAh or more
		(After standard charge and discharge 400 mA till cut off at 23ºC,
		then measure the capacity)
(8)	Initial impedance	100m ohm or less
(9)	Cycle life capacity	1400 mAh or more
		(Repeat the routine - Standard charge + discharge 2000 mA till cut-off –
		299 times and leave one day, then measure in same condition as initial
		capacity)
(10)	Discharge by temperature	–10ºC	50%
		0ºC	80%
		23ºC	100%
		45ºC	100%
		(After standard charge and discharge 1000 mA till cut-off)
(11)	Storage	1600 mAh or more
		(After standard charge, keep it at 23ºC in 30 days then discharge
		1000 mA at 23ºC till cut-off)

8.2 Power Management

(1)	Printable lines	40,000 lines or more
		(Room temperature, full charge, ASCII slide pattern printing)
(2)	Auto power off time	5 minutes (can be changed between 1 and 60 minutes)
(3)	Low battery detection voltage	6.7V
(4)	Battery release voltage	5.5V

8.3 Power Consumption

Average	1.45A (ASCII slide pattern printing)
Peak	2A
Stand-by	80 mA

— 71 —

Image 73

Contents Command Reference Revision Code Command Function CMP-10 Command SETGS H Xxxx ALL Command DetailsBEL Print Results Sample Program0AH ESC RS ESC SP n Default Sample ProgramESC ! n Default See AlsoBit Function Value END ESC $ n1 n2 ESC % n ESC & m n1 n2 d k Initialize commandESC * m n1 n2 d k Hex Mode Vertical Direction Horizontal Direction DotsMax. Dots IMG1 Page ESC n ESC +Hex Type ESC ESC 3 n Bit Equipment Value ESC = nESC n Hex Track ESC ? nESC @ See Also Sample Program Print Results ESC D n k NULESC E n ESC G n ESC R n ESC J nHex Character Set ESC T ESC S nHex Speed bps Model CMP-10 VerHex Condition ESC V nESC Y n Byte ESC ZUpdate via firmware interface Not in use Reserved, always Byte ESC \ n1 n2 ESC ` Hex Position ESC a nESC c5 n ESC d n ESC ESC x n Default Initial value of n is Sample Program GS n m Memory Switch OFFSee Also Sample Program GS * n1 n2 d n1 n2 D1 ...... DnHex Name Dot Density Vertical Direction Horizontal Direction GS / m1DH3AH Hex Printing Position GS H nGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex GS n1 n2 n3 Hex ModeBit Status Item Addressed by ABS GS a nNot in use Thermal head is overheated Disabled for ASB may also have changed Hex Font GS f n1DH68Hn Bar code system Range of k Range of d GS k m d1 ..... dk NUL GS k m n d1 ...... dnBar code system Range of n Range of d For For Standard ModeDescription of Bar Codes JAN-8EAN Code set a Code set B Code set C HexDescriptionof Bar Codes Type Print Sample Outline of Symbol Max. ColumnGS w nL nH ESC l n Black Mark FunctionDistance from PE sensor and print head is approx .5 mm Character Codes Table Programming Considerations Serial Interface Pin No Signal Direction Function Pin No. of Cable14, 15 pin Communicate mode setting Explanation of Input/Output SignalsRS-232C Circuit Electrical CharacteristicsIrComm 3 Wire raw IrLPT Infrared Communication SpecificationsPrinter Mechanism Mechanical SpecificationBattery Power Related SpecificationsEMI Standard AC Adaptor