Citizen CMP-10 manual ESC ! n, Bit Function Value, Default See Also

Page 11

ESC ! n

[Function]	Collective Specifying Printing Mode
[Code]	<1B>H<21>H<n>
[Range]	{0 =< n =< FF(Hex)}
[Outline]	Printing mode is assigned.

	Bit	Function	Value
	Bit	Function	0	1
			0	1
	0	Character Font	Font A	Font B
	1	Undefined
	2	Undefined
	3	High-lighting	Canceled	Specified
	4	Double height	Canceled	Specified
	5	Double width	Canceled	Specified
	6	Undefined
	7	Underline	Canceled	Specified

	Each n bit indicates the following:
[Caution]	• With double height and double width being specified simultaneously, double wide
	and double high characters are consisted.

•An underline is attached to the full character width, which, however, is not attached to the part having been skipped by the horizontal tab.

Neither is it attached to 90°-right-turned characters.

•The underline width is as having been specified by <ESC ->. (The default setting is 1 dot width.)

•n case that double wide character and normal character exist in same one line, the layout of underline is consistent one.

[Default]	n = 0
[See Also]	ESC E, ESC –

— 9 —

Image 11

Contents Command Reference Revision Code Command Function CMP-10 Command SETGS H Xxxx ALL Command DetailsBEL Print Results Sample Program0AH ESC RS ESC SP n Default Sample ProgramBit Function Value Default See AlsoESC ! n END ESC $ n1 n2 ESC % n ESC & m n1 n2 d k Initialize commandMax. Dots Hex Mode Vertical Direction Horizontal Direction DotsESC * m n1 n2 d k IMG1 Page Hex Type ESC +ESC n ESC ESC 3 n Bit Equipment Value ESC = nESC n Hex Track ESC ? nESC @ See Also Sample Program Print Results ESC D n k NULESC E n ESC G n Hex Character Set ESC J nESC R n Model CMP-10 Ver ESC S nESC T Hex Speed bpsHex Condition ESC V nESC Y n Byte ESC ZUpdate via firmware interface Not in use Reserved, always Byte ESC \ n1 n2 ESC ` Hex Position ESC a nESC c5 n ESC d n ESC ESC x n Default Initial value of n is Sample Program GS n m Memory Switch OFFSee Also Sample Program GS * n1 n2 d n1 n2 D1 ...... DnHex Name Dot Density Vertical Direction Horizontal Direction GS / m1DH3AH Hex Printing Position GS H nGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex GS n1 n2 n3 Hex ModeBit Status Item Addressed by ABS GS a nNot in use Thermal head is overheated Disabled for ASB may also have changed Hex Font GS f n1DH68Hn Bar code system Range of n Range of d GS k m d1 ..... dk NUL GS k m n d1 ...... dnBar code system Range of k Range of d Description of Bar Codes For Standard ModeFor JAN-8EAN Code set a Code set B Code set C HexDescriptionof Bar Codes Type Print Sample Outline of Symbol Max. ColumnGS w nL nH ESC l n Black Mark FunctionDistance from PE sensor and print head is approx .5 mm Character Codes Table Programming Considerations Serial Interface Pin No Signal Direction Function Pin No. of Cable14, 15 pin Communicate mode setting Explanation of Input/Output SignalsRS-232C Circuit Electrical CharacteristicsIrComm 3 Wire raw IrLPT Infrared Communication SpecificationsPrinter Mechanism Mechanical SpecificationBattery Power Related SpecificationsEMI Standard AC Adaptor