Citizen CMP-10 manual Infrared Communication Specifications, IrComm 3 Wire raw IrLPT

Page 71

6.INFRARED COMMUNICATION SPECIFICATIONS

6.1Basic Specification

(1)	Interface:	Infrared transceiver mode
(2)	Data transfer system	Half duplex
		Asynchronous
(3)	Baud rate:	9600, 19200, 38400, 57600, 115200 bps
		(Max baud rate can be set at 57600 bps by command.)
(4)	Data configuration	Data length	8 bit
		Stop bit	1 bit
		Parity	None
(5)	Logic level	Low Level = 0
		High Level = 1
(6)	Transport wave:	Wave length 850 - 900 nm
(8)	Distance	Less than 80 cm
(9)	Receiving angle	Left 15º	Right 15º
		Top 15º	Bottom 15º

6.2 Supported Protocol

(1)	IrDA version	1.0
(2)	Flow control	IrDA standard
(3)	Supported Protocol	IrComm 3 wire raw
		IrLPT
		IrLMP
		IrLAP

(4)Protocol Layer

IrComm 3 Wire raw

IrLPT

	Ir Link Management - MUX - IrLMP
	Ir Link Access Protocol - IrLAP
		Async Serial-IR
		9600-115.2 kb/s
(5) Applicable protocol	Class:	IrDA:IrCOMM or IrDA:IrLPT
	Attribute:	IrDA:IrLMP:LsapSel
		via IrLMP

— 69 —

Image 71

Contents Command Reference Revision Code Command Function CMP-10 Command SETGS H Xxxx ALL Command DetailsBEL Print Results Sample Program0AH ESC RS ESC SP n Default Sample ProgramBit Function Value Default See AlsoESC ! n END ESC $ n1 n2 ESC % n ESC & m n1 n2 d k Initialize commandMax. Dots Hex Mode Vertical Direction Horizontal Direction DotsESC * m n1 n2 d k IMG1 Page Hex Type ESC +ESC n ESC ESC 3 n Bit Equipment Value ESC = nESC n Hex Track ESC ? nESC @ See Also Sample Program Print Results ESC D n k NULESC E n ESC G n Hex Character Set ESC J nESC R n Model CMP-10 Ver ESC S nESC T Hex Speed bpsHex Condition ESC V nESC Y n Byte ESC ZUpdate via firmware interface Not in use Reserved, always Byte ESC \ n1 n2 ESC ` Hex Position ESC a nESC c5 n ESC d n ESC ESC x n Default Initial value of n is Sample Program GS n m Memory Switch OFFSee Also Sample Program GS * n1 n2 d n1 n2 D1 ...... DnHex Name Dot Density Vertical Direction Horizontal Direction GS / m1DH3AH Hex Printing Position GS H nGS L nL nH GS W n NL = 40 Hex, nH = 2 Hex GS n1 n2 n3 Hex ModeBit Status Item Addressed by ABS GS a nNot in use Thermal head is overheated Disabled for ASB may also have changed Hex Font GS f n1DH68Hn Bar code system Range of n Range of d GS k m d1 ..... dk NUL GS k m n d1 ...... dnBar code system Range of k Range of d Description of Bar Codes For Standard ModeFor JAN-8EAN Code set a Code set B Code set C HexDescriptionof Bar Codes Type Print Sample Outline of Symbol Max. ColumnGS w nL nH ESC l n Black Mark FunctionDistance from PE sensor and print head is approx .5 mm Character Codes Table Programming Considerations Serial Interface Pin No Signal Direction Function Pin No. of Cable14, 15 pin Communicate mode setting Explanation of Input/Output SignalsRS-232C Circuit Electrical CharacteristicsIrComm 3 Wire raw IrLPT Infrared Communication SpecificationsPrinter Mechanism Mechanical SpecificationBattery Power Related SpecificationsEMI Standard AC Adaptor