M-S Cash Drawer 7193 Ordering Paper and Supplies, Ordering Thermal Paper, Recommended Suppliers

Page 11

About the 7193 Printer

7193 Owner’s Guide

Ordering Paper and Supplies

Thermal receipt paper and other supplies can be ordered from several recommended and qualified suppliers.

Ordering Thermal Paper

The 7193 requires “fax grade” thermal paper with the following dimensions:

Diameter: 80 mm maximum (3.15 in.)

Length: 83 meters (273 ft.)

Width: 80 mm ± .5 mm (3.15 ± .008 in.)

The paper must not be attached at the core or the printer will be damaged when the paper runs out. When the paper runs out, the printer stops printing and turns on the Paper Out light (red) on the operator panel. There is no indication or automatic signal when the paper runs low. It is recommended that you use a paper roll with a colored stripe at the end of the roll to indicate that the paper is running low.

Recommended Suppliers

The grades of paper listed here will give the best print quality. When more than one stock or paper grade number is listed, the first number (standard density) provides better image density. You may order paper directly from AT&T Global Information Solutions. Contact your Axiohm supplier for ordering paper manufactured by Kanzaki (paper grades listed on the next page).

AT&T Global Information Solutions Company

Media Products Division

9995 Washington Church Road Miamisburg, OH 45342

Voice: 1(800)543-8130 (toll free), or local listing of Media Products sales office

Stock numbers: 878559 (standard density), 856966 (light density)

4

May 1996

Image 11
Contents Owners Guide Information to User Quick Reference Who Should Use this Book? How to Use This BookHow to Obtain More Information Contents Solving Problems Appendix B Print Characteristics 107 About the 7193 Printer Options FeaturesModels Communication InterfacesThermal Printhead Recommended Suppliers Ordering Paper and SuppliesOrdering Thermal Paper Kanzaki Specialty Papers Other Qualified SuppliersOrdering Cash Drawers Ordering the Power Supply and CablesOrdering the Printer Wall-Mount Kit Cleaning the Printer Removing the Packing Material What Is in the Box?Repacking the Printer Choosing a Location Setting Switches Owner’s Guide Attaching the Feet Connecting Cash Drawer Cables RS-232C Models Connecting Communication and Power CablesParallel Models Turning On the Printer Loading and Changing Paper When to Change the PaperRemoving the Paper Roll Putting In the Paper Roll Advancing Paper Testing the Printer 3cx39pi Mounting the Printer on a Wall Bracket Mounting the Power Supply on a Wall Holder Operator Panel Lights Solving ProblemsOperator-Correctable Conditions Correcting ProblemsService-Related Problems Print is Light or Spotty Contacting a Service RepresentativeNo Power to Printer or Power Voltages Incorrect Level 0 Diagnostics DiagnosticsEerom Level 1 DiagnosticsSetting Data Error and Data Buffer options Setting Printhead Resistance Setting Default Lines per Inch Setting Partial Cut Distance Ignoring/Using the Carriage Return Enter the Data Scope Mode Running the Data Scope Mode1BH Exit the Data Scope ModeTesting Receipt Printing Level 3 Diagnostics Level 2 DiagnosticsInterfaces Sending CommandsCommunication Overview RS-232C Interface Using DOS to Send CommandsUsing Basic to Send Commands DTR/DSR Protocol XON/XOFF ProtocolConnectors RS-232C Technical SpecificationsCash Drawer Connectors Switch Settings OFF Parallel Protocol Parallel InterfaceParallel Connectors Parallel Technical SpecificationsParallel Printers Parallel Switch Settings Command List CommandsPrinter Function Commands Owner’s Guide Print Characteristics Commands Printer Status Commands Graphics CommandsBar Code Commands Real Time CommandsLine Feed Command DescriptionsHorizontal Tab Feed n Print Lines Carriage ReturnClear Printer Print Feed n Dot RowsAdd n Extra Dot Rows Set Column Full Knife CutPartial Knife Cut Generate ToneSet Absolute Starting Position Set Character Right-Side SpacingInitialize Printer Set Line Spacing to 1/6 InchSet Line Spacing to n Minimum Units Select PrinterPrint and Feed n Minimum Units Set Horizontal Tab PositionsSet Relative Starting Position Print and Feed n Lines Enable or Disable Panel SwitchAlign Character Positions Select Sensors to Stop PrintingWrite to Non-Volatile Memory Read from Non-Volatile MemoryGenerate Pulse to Open Cash Drawer Rotate Characters Counter-Clockwise Select Double-Wide CharactersSelect Single-Wide Characters Select Pitch Column Width Set Print ModeDefine User-Defined Character Set Select Character SetSelect Character Code Table Copy Character Set from ROM to RAMSet or Cancel Upside-Down Characters Set or Cancel Rotated Characters ClockwiseSummary of Rotated Printing Set Bit Image Mode N1 + 256 x n2 N1 + 256 x n2 Number of Bytes of Data Double-Density Graphics Single-Density GraphicsDefine Downloaded Bit Image Print Downloaded Bit Image Transmit Cash Drawer Status Request Alternate Status Transmit Printer Status First Implementation Alternate Implementation Rules for Using Real Time CommandsMoving Data Through the Buffer Busy Line and Fault Conditions GS Sequence Real Time Status Transmission= Transmit Printer Status = Transmit RS-232C Busy Status = Transmit Receipt Paper Status Real Time Request to PrinterDLE Sequence Real Time Printer Status Transmission Clear Printer CommandRecognizing Data from the Printer Select Height of Bar Code Select Printing Position of HRI CharactersSelect Pitch of HRI Characters JAN8 EAN Print Bar CodeSelect Width of Bar Code Print Code 128 Bar CodeReliability Appendix a SpecificationsEnvironmental Conditions Power RequirementsPrinting Specifications Dimensions and WeightPrint Zones Duty Cycle Restrictions Printing Solid Blocks Density of Receipt Print LinesAppendix B Print Characteristics Appendix B Print Characteristics Owner’s Guide 110 May May Index Index112 Owner’s Guide Owner’s Guide 114 Owner’s Guide Owner’s Guide Axiohm IPB