M-S Cash Drawer 7193 Ordering the Power Supply and Cables, Ordering the Printer Wall-Mount Kit

Page 13

About the 7193 Printer

7193 Owner’s Guide

Ordering the Power Supply and Cables

Contact your Axiohm supplier to order the power supply and cables. The Axiohm numbers are for reference only. Suppliers may use different numbers.

∙Power supply with attached cable (to printer)

and wall-mount kit:

7193-F301

∙Separate power supply cord (to outlet) Order for appropriate power connector

∙ United States:

7193-F320

∙International:7193-F321

∙	United Kingdom:	7193-F322
∙	S.E.V.:	7193-F323
∙	Australia:	7193-F324
∙	Japan:	7193-F325

∙Communication cables

∙ RS-232C 25-pin (host) to 9-pin:

		1420-C001-0030 (3 meters—9.8 ft.)
∙	RS-232C 9-pin to 9-pin:	1416-C057-0030 (3 meters—9.8 ft.)
∙	Parallel 25-pin to 25-pin:	1420-C003-0030 (3 meters—9.8 ft.)

Ordering the Printer Wall-Mount Kit

Contact your Axiohm supplier to order the printer wall-mount kit. The Axiohm number below is for reference only. Other suppliers may use a different number.

Printer wall-mount kit:

7193-K260-V001

Ordering Cash Drawers

The following cash drawers may be used with the 7193 printer:

∙AT&T Global Information Solutions

	(NCR Cash Drawer):	Model 7052-K657
∙ M-S Cash Drawer Corp.:		Model EP-125 K series,
		EP-127, EP-102
∙	APG Cash Drawer:	Model 237
∙	Indiana Cash Drawer:	Model SLD

6

May 1996

Image 13

Contents Owners Guide Information to User Quick Reference How to Obtain More Information How to Use This BookWho Should Use this Book? Contents Solving Problems Appendix B Print Characteristics 107 About the 7193 Printer Models FeaturesCommunication Interfaces OptionsThermal Printhead Ordering Thermal Paper Ordering Paper and SuppliesRecommended Suppliers Kanzaki Specialty Papers Other Qualified SuppliersOrdering the Printer Wall-Mount Kit Ordering the Power Supply and CablesOrdering Cash Drawers Cleaning the Printer Removing the Packing Material What Is in the Box?Repacking the Printer Choosing a Location Setting Switches Owner’s Guide Attaching the Feet Connecting Cash Drawer Cables RS-232C Models Connecting Communication and Power CablesParallel Models Turning On the Printer Loading and Changing Paper When to Change the PaperRemoving the Paper Roll Putting In the Paper Roll Advancing Paper Testing the Printer 3cx39pi Mounting the Printer on a Wall Bracket Mounting the Power Supply on a Wall Holder Operator Panel Lights Solving ProblemsService-Related Problems Correcting ProblemsOperator-Correctable Conditions No Power to Printer or Power Voltages Incorrect Contacting a Service RepresentativePrint is Light or Spotty Level 0 Diagnostics DiagnosticsEerom Level 1 DiagnosticsSetting Data Error and Data Buffer options Setting Printhead Resistance Setting Default Lines per Inch Setting Partial Cut Distance Ignoring/Using the Carriage Return Enter the Data Scope Mode Running the Data Scope Mode1BH Exit the Data Scope ModeTesting Receipt Printing Level 3 Diagnostics Level 2 DiagnosticsCommunication Overview Sending CommandsInterfaces Using Basic to Send Commands Using DOS to Send CommandsRS-232C Interface DTR/DSR Protocol XON/XOFF ProtocolConnectors RS-232C Technical SpecificationsCash Drawer Connectors Switch Settings OFF Parallel Protocol Parallel InterfaceParallel Connectors Parallel Technical SpecificationsParallel Printers Parallel Switch Settings Command List CommandsPrinter Function Commands Owner’s Guide Print Characteristics Commands Printer Status Commands Graphics CommandsBar Code Commands Real Time CommandsHorizontal Tab Command DescriptionsLine Feed Clear Printer Carriage ReturnFeed n Print Lines Add n Extra Dot Rows Feed n Dot RowsPrint Partial Knife Cut Full Knife CutGenerate Tone Set ColumnSet Absolute Starting Position Set Character Right-Side SpacingSet Line Spacing to n Minimum Units Set Line Spacing to 1/6 InchSelect Printer Initialize PrinterPrint and Feed n Minimum Units Set Horizontal Tab PositionsSet Relative Starting Position Align Character Positions Enable or Disable Panel SwitchSelect Sensors to Stop Printing Print and Feed n LinesGenerate Pulse to Open Cash Drawer Read from Non-Volatile MemoryWrite to Non-Volatile Memory Select Single-Wide Characters Select Double-Wide CharactersRotate Characters Counter-Clockwise Select Pitch Column Width Set Print ModeDefine User-Defined Character Set Select Character SetSelect Character Code Table Copy Character Set from ROM to RAMSet or Cancel Upside-Down Characters Set or Cancel Rotated Characters ClockwiseSummary of Rotated Printing Set Bit Image Mode N1 + 256 x n2 N1 + 256 x n2 Number of Bytes of Data Double-Density Graphics Single-Density GraphicsDefine Downloaded Bit Image Print Downloaded Bit Image Transmit Cash Drawer Status Request Alternate Status Transmit Printer Status First Implementation Alternate Implementation Rules for Using Real Time CommandsMoving Data Through the Buffer Busy Line and Fault Conditions GS Sequence Real Time Status Transmission= Transmit Printer Status = Transmit RS-232C Busy Status = Transmit Receipt Paper Status Real Time Request to PrinterDLE Sequence Real Time Printer Status Transmission Clear Printer CommandRecognizing Data from the Printer Select Pitch of HRI Characters Select Printing Position of HRI CharactersSelect Height of Bar Code JAN8 EAN Print Bar CodeSelect Width of Bar Code Print Code 128 Bar CodeReliability Appendix a SpecificationsEnvironmental Conditions Power RequirementsPrinting Specifications Dimensions and WeightPrint Zones Duty Cycle Restrictions Printing Solid Blocks Density of Receipt Print LinesAppendix B Print Characteristics Appendix B Print Characteristics Owner’s Guide 110 May May Index Index112 Owner’s Guide Owner’s Guide 114 Owner’s Guide Owner’s Guide Axiohm IPB