M-S Cash Drawer 7193 manual Set Line Spacing to 1/6 Inch, Set Line Spacing to n Minimum Units

Page 71

Commands

7193 Owner’s Guide

Set Line Spacing to 1/6 Inch

Sets the line spacing to 1/6 of an inch (4.25 mm). It is not affected by the Print

(17)command.

Hex	Decimal	ASCII	Default
1B 32	27 50	ESC 2	0.13 Inch (3.33 mm)

Set Line Spacing to n Minimum Units

Sets the line spacing to n/360 of an inch. The minimum line spacing is 8.5 lines per inch. The line spacing equals the character height when n is too small.

Hex	Decimal	ASCII	Value of n	Default
1B 33 n	27 51 n	ESC 3 n	0-255	0.13 Inch (3.33 mm)

Select Printer

This command is not implemented and is ignored if received.

Hex	Decimal	ASCII	Value of n		Default
1B 3D n	27 61 n	ESC = n	0	(bit 0), printer not selected	1
			1	(bit 0), printer selected

Initialize Printer

Clears the print line buffer and resets the printer to the following default selections (startup configuration):

∙Single-Wide, Single-High, Non-Rotated, and Left-Aligned characters are set

∙Extra Dot Rows are set to two

∙User-defined characters or logo graphics (from RAM) are cleared

∙Character Set is set to Code Page 437 (default)

∙Character Pitch is reset to 15.2 CPI and column width to 44 (default)

∙Returns paper exhaust to the paper status line if an alternate status has been requested (Parallel interface only)

Hex	Decimal	ASCII
1B 40	27 64	ESC @

68

May 1996

Image 71

Contents Owners Guide Information to User Quick Reference Who Should Use this Book? How to Use This BookHow to Obtain More Information Contents Solving Problems Appendix B Print Characteristics 107 About the 7193 Printer Options FeaturesModels Communication InterfacesThermal Printhead Recommended Suppliers Ordering Paper and SuppliesOrdering Thermal Paper Kanzaki Specialty Papers Other Qualified SuppliersOrdering Cash Drawers Ordering the Power Supply and CablesOrdering the Printer Wall-Mount Kit Cleaning the Printer Removing the Packing Material What Is in the Box?Repacking the Printer Choosing a Location Setting Switches Owner’s Guide Attaching the Feet Connecting Cash Drawer Cables RS-232C Models Connecting Communication and Power CablesParallel Models Turning On the Printer Loading and Changing Paper When to Change the PaperRemoving the Paper Roll Putting In the Paper Roll Advancing Paper Testing the Printer 3cx39pi Mounting the Printer on a Wall Bracket Mounting the Power Supply on a Wall Holder Operator Panel Lights Solving ProblemsOperator-Correctable Conditions Correcting ProblemsService-Related Problems Print is Light or Spotty Contacting a Service RepresentativeNo Power to Printer or Power Voltages Incorrect Level 0 Diagnostics DiagnosticsEerom Level 1 DiagnosticsSetting Data Error and Data Buffer options Setting Printhead Resistance Setting Default Lines per Inch Setting Partial Cut Distance Ignoring/Using the Carriage Return Enter the Data Scope Mode Running the Data Scope Mode1BH Exit the Data Scope ModeTesting Receipt Printing Level 3 Diagnostics Level 2 DiagnosticsInterfaces Sending CommandsCommunication Overview RS-232C Interface Using DOS to Send CommandsUsing Basic to Send Commands DTR/DSR Protocol XON/XOFF ProtocolConnectors RS-232C Technical SpecificationsCash Drawer Connectors Switch Settings OFF Parallel Protocol Parallel InterfaceParallel Connectors Parallel Technical SpecificationsParallel Printers Parallel Switch Settings Command List CommandsPrinter Function Commands Owner’s Guide Print Characteristics Commands Printer Status Commands Graphics CommandsBar Code Commands Real Time CommandsLine Feed Command DescriptionsHorizontal Tab Feed n Print Lines Carriage ReturnClear Printer Print Feed n Dot RowsAdd n Extra Dot Rows Set Column Full Knife CutPartial Knife Cut Generate ToneSet Absolute Starting Position Set Character Right-Side SpacingInitialize Printer Set Line Spacing to 1/6 InchSet Line Spacing to n Minimum Units Select PrinterPrint and Feed n Minimum Units Set Horizontal Tab PositionsSet Relative Starting Position Print and Feed n Lines Enable or Disable Panel SwitchAlign Character Positions Select Sensors to Stop PrintingWrite to Non-Volatile Memory Read from Non-Volatile MemoryGenerate Pulse to Open Cash Drawer Rotate Characters Counter-Clockwise Select Double-Wide CharactersSelect Single-Wide Characters Select Pitch Column Width Set Print ModeDefine User-Defined Character Set Select Character SetSelect Character Code Table Copy Character Set from ROM to RAMSet or Cancel Upside-Down Characters Set or Cancel Rotated Characters ClockwiseSummary of Rotated Printing Set Bit Image Mode N1 + 256 x n2 N1 + 256 x n2 Number of Bytes of Data Double-Density Graphics Single-Density GraphicsDefine Downloaded Bit Image Print Downloaded Bit Image Transmit Cash Drawer Status Request Alternate Status Transmit Printer Status First Implementation Alternate Implementation Rules for Using Real Time CommandsMoving Data Through the Buffer Busy Line and Fault Conditions GS Sequence Real Time Status Transmission= Transmit Printer Status = Transmit RS-232C Busy Status = Transmit Receipt Paper Status Real Time Request to PrinterDLE Sequence Real Time Printer Status Transmission Clear Printer CommandRecognizing Data from the Printer Select Height of Bar Code Select Printing Position of HRI CharactersSelect Pitch of HRI Characters JAN8 EAN Print Bar CodeSelect Width of Bar Code Print Code 128 Bar CodeReliability Appendix a SpecificationsEnvironmental Conditions Power RequirementsPrinting Specifications Dimensions and WeightPrint Zones Duty Cycle Restrictions Printing Solid Blocks Density of Receipt Print LinesAppendix B Print Characteristics Appendix B Print Characteristics Owner’s Guide 110 May May Index Index112 Owner’s Guide Owner’s Guide 114 Owner’s Guide Owner’s Guide Axiohm IPB