M-S Cash Drawer 7193 manual RS-232C Technical Specifications, Connectors

Page 52

Communication

7193 Owner’s Guide

RS-232C Technical Specifications

This section describes the pin settings for the connectors and the RS-232C interface parameters.

Connectors

The following illustration shows the RS-232C communication connector and pin assignments. The connector is a 9-pin male D-shell connector and is located in the hollow cavity under the printer.

Function Pin Numbers Function

Logic Ground 5

9 Not Used

DTR 4

8 CTS

TXD 3

7 RTS

RXD 2

6 DSR

Not Used 1

Shell - Frame Ground

Printer View (Male)

With RS-232C, the 7193 is always remotely powered. The following illustration shows the power cable connector and pin assignments. The power cable connector is 6-pin mini DIN plug and is located in the small cavity under the printer at the front.

Shell Frame Ground

Return 5

6 +24 Volts

Return 3

4 +24 Volts

Return 1

2 +24 Volts

Pin View End

48

May 1996

Image 52

Contents Owners Guide Information to User Quick Reference How to Obtain More Information How to Use This BookWho Should Use this Book? Contents Solving Problems Appendix B Print Characteristics 107 About the 7193 Printer Features ModelsCommunication Interfaces OptionsThermal Printhead Ordering Thermal Paper Ordering Paper and SuppliesRecommended Suppliers Other Qualified Suppliers Kanzaki Specialty PapersOrdering the Printer Wall-Mount Kit Ordering the Power Supply and CablesOrdering Cash Drawers Cleaning the Printer What Is in the Box? Removing the Packing MaterialRepacking the Printer Choosing a Location Setting Switches Owner’s Guide Attaching the Feet Connecting Cash Drawer Cables Connecting Communication and Power Cables RS-232C ModelsParallel Models Turning On the Printer When to Change the Paper Loading and Changing PaperRemoving the Paper Roll Putting In the Paper Roll Advancing Paper Testing the Printer 3cx39pi Mounting the Printer on a Wall Bracket Mounting the Power Supply on a Wall Holder Solving Problems Operator Panel LightsService-Related Problems Correcting ProblemsOperator-Correctable Conditions No Power to Printer or Power Voltages Incorrect Contacting a Service RepresentativePrint is Light or Spotty Diagnostics Level 0 DiagnosticsLevel 1 Diagnostics EeromSetting Data Error and Data Buffer options Setting Printhead Resistance Setting Default Lines per Inch Setting Partial Cut Distance Ignoring/Using the Carriage Return Running the Data Scope Mode Enter the Data Scope ModeExit the Data Scope Mode 1BHTesting Receipt Printing Level 2 Diagnostics Level 3 DiagnosticsCommunication Overview Sending CommandsInterfaces Using Basic to Send Commands Using DOS to Send CommandsRS-232C Interface XON/XOFF Protocol DTR/DSR ProtocolRS-232C Technical Specifications ConnectorsCash Drawer Connectors Switch Settings OFF Parallel Interface Parallel ProtocolParallel Technical Specifications Parallel ConnectorsParallel Printers Parallel Switch Settings Commands Command ListPrinter Function Commands Owner’s Guide Print Characteristics Commands Graphics Commands Printer Status CommandsReal Time Commands Bar Code CommandsHorizontal Tab Command DescriptionsLine Feed Clear Printer Carriage ReturnFeed n Print Lines Add n Extra Dot Rows Feed n Dot RowsPrint Full Knife Cut Partial Knife CutGenerate Tone Set ColumnSet Character Right-Side Spacing Set Absolute Starting PositionSet Line Spacing to 1/6 Inch Set Line Spacing to n Minimum UnitsSelect Printer Initialize PrinterSet Horizontal Tab Positions Print and Feed n Minimum UnitsSet Relative Starting Position Enable or Disable Panel Switch Align Character PositionsSelect Sensors to Stop Printing Print and Feed n LinesGenerate Pulse to Open Cash Drawer Read from Non-Volatile MemoryWrite to Non-Volatile Memory Select Single-Wide Characters Select Double-Wide CharactersRotate Characters Counter-Clockwise Set Print Mode Select Pitch Column WidthSelect Character Set Define User-Defined Character SetCopy Character Set from ROM to RAM Select Character Code TableSet or Cancel Rotated Characters Clockwise Set or Cancel Upside-Down CharactersSummary of Rotated Printing Set Bit Image Mode N1 + 256 x n2 N1 + 256 x n2 Number of Bytes of Data Single-Density Graphics Double-Density GraphicsDefine Downloaded Bit Image Print Downloaded Bit Image Transmit Cash Drawer Status Request Alternate Status Transmit Printer Status First Implementation Rules for Using Real Time Commands Alternate ImplementationMoving Data Through the Buffer Busy Line and Fault Conditions Real Time Status Transmission GS Sequence= Transmit Printer Status = Transmit RS-232C Busy Status Real Time Request to Printer = Transmit Receipt Paper StatusDLE Sequence Clear Printer Command Real Time Printer Status TransmissionRecognizing Data from the Printer Select Pitch of HRI Characters Select Printing Position of HRI CharactersSelect Height of Bar Code Print Bar Code JAN8 EANPrint Code 128 Bar Code Select Width of Bar CodeAppendix a Specifications ReliabilityPower Requirements Environmental ConditionsDimensions and Weight Printing SpecificationsPrint Zones Density of Receipt Print Lines Duty Cycle Restrictions Printing Solid BlocksAppendix B Print Characteristics Appendix B Print Characteristics Owner’s Guide 110 May Index May Index112 Owner’s Guide Owner’s Guide 114 Owner’s Guide Owner’s Guide Axiohm IPB