M-S Cash Drawer 7193 manual What Is in the Box?, Removing the Packing Material

Page 15

7193 Owner’s Guide

Setting Up the Printer

Setting Up the Printer

What Is in the Box?

The following items are packed in the shipping box:

∙Printer enclosed in a plastic bag and foam pack

∙Thermal paper roll, wrapped with a foam strip (inside printer)

∙Test printout protecting the printhead (inside printer)

∙7193 Setup and User's Guide

∙Rubber feet and hook and loop fasteners (fasteners used to anchor printer)

∙Power supply with attached cable (to printer) and related items

∙Power cord (from power supply to outlet)

∙Wall-mount holder for the power supply with screws and wall anchors

∙Tie-wrap for cable

These items may be ordered as options and will be shipped separately:

∙Wall-mount kit for the printer

∙Communication cable (from host system to printer)

∙Cash drawer with cables (see “Ordering Cash Drawers” on page 6)

Removing the Packing Material

1.Remove the printer from the foam pack and open the receipt cover by pulling up on the front left corner.

2.Remove the paper roll and test printout from inside the printer.

3.Remove the foam strip from around the paper roll.

4.Save all packing materials for future storing, moving, or shipping the printer.

May 1996

Image 15

Contents Owners Guide Information to User Quick Reference How to Use This Book How to Obtain More InformationWho Should Use this Book? Contents Solving Problems Appendix B Print Characteristics 107 About the 7193 Printer Options FeaturesModels Communication InterfacesThermal Printhead Ordering Paper and Supplies Ordering Thermal PaperRecommended Suppliers Kanzaki Specialty Papers Other Qualified SuppliersOrdering the Power Supply and Cables Ordering the Printer Wall-Mount KitOrdering Cash Drawers Cleaning the Printer Removing the Packing Material What Is in the Box?Repacking the Printer Choosing a Location Setting Switches Owner’s Guide Attaching the Feet Connecting Cash Drawer Cables RS-232C Models Connecting Communication and Power CablesParallel Models Turning On the Printer Loading and Changing Paper When to Change the PaperRemoving the Paper Roll Putting In the Paper Roll Advancing Paper Testing the Printer 3cx39pi Mounting the Printer on a Wall Bracket Mounting the Power Supply on a Wall Holder Operator Panel Lights Solving ProblemsCorrecting Problems Service-Related ProblemsOperator-Correctable Conditions Contacting a Service Representative No Power to Printer or Power Voltages IncorrectPrint is Light or Spotty Level 0 Diagnostics DiagnosticsEerom Level 1 DiagnosticsSetting Data Error and Data Buffer options Setting Printhead Resistance Setting Default Lines per Inch Setting Partial Cut Distance Ignoring/Using the Carriage Return Enter the Data Scope Mode Running the Data Scope Mode1BH Exit the Data Scope ModeTesting Receipt Printing Level 3 Diagnostics Level 2 DiagnosticsSending Commands Communication OverviewInterfaces Using DOS to Send Commands Using Basic to Send CommandsRS-232C Interface DTR/DSR Protocol XON/XOFF ProtocolConnectors RS-232C Technical SpecificationsCash Drawer Connectors Switch Settings OFF Parallel Protocol Parallel InterfaceParallel Connectors Parallel Technical SpecificationsParallel Printers Parallel Switch Settings Command List CommandsPrinter Function Commands Owner’s Guide Print Characteristics Commands Printer Status Commands Graphics CommandsBar Code Commands Real Time CommandsCommand Descriptions Horizontal TabLine Feed Carriage Return Clear PrinterFeed n Print Lines Feed n Dot Rows Add n Extra Dot RowsPrint Set Column Full Knife CutPartial Knife Cut Generate ToneSet Absolute Starting Position Set Character Right-Side SpacingInitialize Printer Set Line Spacing to 1/6 InchSet Line Spacing to n Minimum Units Select PrinterPrint and Feed n Minimum Units Set Horizontal Tab PositionsSet Relative Starting Position Print and Feed n Lines Enable or Disable Panel SwitchAlign Character Positions Select Sensors to Stop PrintingRead from Non-Volatile Memory Generate Pulse to Open Cash DrawerWrite to Non-Volatile Memory Select Double-Wide Characters Select Single-Wide CharactersRotate Characters Counter-Clockwise Select Pitch Column Width Set Print ModeDefine User-Defined Character Set Select Character SetSelect Character Code Table Copy Character Set from ROM to RAMSet or Cancel Upside-Down Characters Set or Cancel Rotated Characters ClockwiseSummary of Rotated Printing Set Bit Image Mode N1 + 256 x n2 N1 + 256 x n2 Number of Bytes of Data Double-Density Graphics Single-Density GraphicsDefine Downloaded Bit Image Print Downloaded Bit Image Transmit Cash Drawer Status Request Alternate Status Transmit Printer Status First Implementation Alternate Implementation Rules for Using Real Time CommandsMoving Data Through the Buffer Busy Line and Fault Conditions GS Sequence Real Time Status Transmission= Transmit Printer Status = Transmit RS-232C Busy Status = Transmit Receipt Paper Status Real Time Request to PrinterDLE Sequence Real Time Printer Status Transmission Clear Printer CommandRecognizing Data from the Printer Select Printing Position of HRI Characters Select Pitch of HRI CharactersSelect Height of Bar Code JAN8 EAN Print Bar CodeSelect Width of Bar Code Print Code 128 Bar CodeReliability Appendix a SpecificationsEnvironmental Conditions Power RequirementsPrinting Specifications Dimensions and WeightPrint Zones Duty Cycle Restrictions Printing Solid Blocks Density of Receipt Print LinesAppendix B Print Characteristics Appendix B Print Characteristics Owner’s Guide 110 May May Index Index112 Owner’s Guide Owner’s Guide 114 Owner’s Guide Owner’s Guide Axiohm IPB