M-S Cash Drawer 7193 manual Exit the Data Scope Mode, 1BH

Page 46

7193 Owner’s Guide

Diagnostics

1BH

61H 00H 1BH 64H 06H 1BH 6DH 16 H0CH 1BH 21H 30H 20H 37H 31H 35H 36H 20H 54H 68H 65H 72H 6DH 61H 6CH 2FH 49H 6DH 70H 61H 63H 74H 0AH 1BH 21H 20H 54H 54H 77H 6FH 20H 48H 65H 61H

Datascope Mode Print Test

Exit the Data Scope Mode

1.Turn the power off.

2.Set the switches to the settings in the table.

Switch 1	Switch 2	Switch 3	Switch 4	Switch 5	Switch 6

On	Off	Off	On	Off	Off

3.Turn the power back on to enter the settings into the EEROM and disable the Data Scope Mode.

The On Line light (green) blinks.

4.Turn the power off.

5.Set the DIP switches to the former settings.

DIP switch 1 must be Off to return the printer to the on-line mode.

6.Turn the power back on.

The printer is on-line and can communicate normally with the host system.

May 1996

Image 46

Contents Owners Guide Information to User Quick Reference How to Obtain More Information How to Use This BookWho Should Use this Book? Contents Solving Problems Appendix B Print Characteristics 107 About the 7193 Printer Communication Interfaces FeaturesModels OptionsThermal Printhead Ordering Thermal Paper Ordering Paper and SuppliesRecommended Suppliers Other Qualified Suppliers Kanzaki Specialty PapersOrdering the Printer Wall-Mount Kit Ordering the Power Supply and CablesOrdering Cash Drawers Cleaning the Printer What Is in the Box? Removing the Packing MaterialRepacking the Printer Choosing a Location Setting Switches Owner’s Guide Attaching the Feet Connecting Cash Drawer Cables Connecting Communication and Power Cables RS-232C ModelsParallel Models Turning On the Printer When to Change the Paper Loading and Changing PaperRemoving the Paper Roll Putting In the Paper Roll Advancing Paper Testing the Printer 3cx39pi Mounting the Printer on a Wall Bracket Mounting the Power Supply on a Wall Holder Solving Problems Operator Panel LightsService-Related Problems Correcting ProblemsOperator-Correctable Conditions No Power to Printer or Power Voltages Incorrect Contacting a Service RepresentativePrint is Light or Spotty Diagnostics Level 0 DiagnosticsLevel 1 Diagnostics EeromSetting Data Error and Data Buffer options Setting Printhead Resistance Setting Default Lines per Inch Setting Partial Cut Distance Ignoring/Using the Carriage Return Running the Data Scope Mode Enter the Data Scope ModeExit the Data Scope Mode 1BHTesting Receipt Printing Level 2 Diagnostics Level 3 DiagnosticsCommunication Overview Sending CommandsInterfaces Using Basic to Send Commands Using DOS to Send CommandsRS-232C Interface XON/XOFF Protocol DTR/DSR ProtocolRS-232C Technical Specifications ConnectorsCash Drawer Connectors Switch Settings OFF Parallel Interface Parallel ProtocolParallel Technical Specifications Parallel ConnectorsParallel Printers Parallel Switch Settings Commands Command ListPrinter Function Commands Owner’s Guide Print Characteristics Commands Graphics Commands Printer Status CommandsReal Time Commands Bar Code CommandsHorizontal Tab Command DescriptionsLine Feed Clear Printer Carriage ReturnFeed n Print Lines Add n Extra Dot Rows Feed n Dot RowsPrint Generate Tone Full Knife CutPartial Knife Cut Set ColumnSet Character Right-Side Spacing Set Absolute Starting PositionSelect Printer Set Line Spacing to 1/6 InchSet Line Spacing to n Minimum Units Initialize PrinterSet Horizontal Tab Positions Print and Feed n Minimum UnitsSet Relative Starting Position Select Sensors to Stop Printing Enable or Disable Panel SwitchAlign Character Positions Print and Feed n LinesGenerate Pulse to Open Cash Drawer Read from Non-Volatile MemoryWrite to Non-Volatile Memory Select Single-Wide Characters Select Double-Wide CharactersRotate Characters Counter-Clockwise Set Print Mode Select Pitch Column WidthSelect Character Set Define User-Defined Character SetCopy Character Set from ROM to RAM Select Character Code TableSet or Cancel Rotated Characters Clockwise Set or Cancel Upside-Down CharactersSummary of Rotated Printing Set Bit Image Mode N1 + 256 x n2 N1 + 256 x n2 Number of Bytes of Data Single-Density Graphics Double-Density GraphicsDefine Downloaded Bit Image Print Downloaded Bit Image Transmit Cash Drawer Status Request Alternate Status Transmit Printer Status First Implementation Rules for Using Real Time Commands Alternate ImplementationMoving Data Through the Buffer Busy Line and Fault Conditions Real Time Status Transmission GS Sequence= Transmit Printer Status = Transmit RS-232C Busy Status Real Time Request to Printer = Transmit Receipt Paper StatusDLE Sequence Clear Printer Command Real Time Printer Status TransmissionRecognizing Data from the Printer Select Pitch of HRI Characters Select Printing Position of HRI CharactersSelect Height of Bar Code Print Bar Code JAN8 EANPrint Code 128 Bar Code Select Width of Bar CodeAppendix a Specifications ReliabilityPower Requirements Environmental ConditionsDimensions and Weight Printing SpecificationsPrint Zones Density of Receipt Print Lines Duty Cycle Restrictions Printing Solid BlocksAppendix B Print Characteristics Appendix B Print Characteristics Owner’s Guide 110 May Index May Index112 Owner’s Guide Owner’s Guide 114 Owner’s Guide Owner’s Guide Axiohm IPB