M-S Cash Drawer 7193 manual Running the Data Scope Mode, Enter the Data Scope Mode

Page 45

Diagnostics

7193 Owner’s Guide

Running the Data Scope Mode

This test prints a Hex dump of all data sent to the printer: “1” prints as Hex 31, “A” as Hex 41 and so on. This helps troubleshoot communication problems, and runs during a normal host application (after being enabled in level 1 diagnostics).

Enter the Data Scope Mode

Caution: The DIP switches are set at the factory to predetermined settings and should generally not be changed. If you must change the settings, do so carefully to avoid changing other functions. Run the print test to see if the Data Scope Mode is on or off. See “Testing The Printer” On Page 23.

1.Turn the power off.

2.Turn the printer over and note what the current DIP switch settings are.

3.Set the switches to the settings in the table.

Switch 1	Switch 2	Switch 3	Switch 4	Switch 5	Switch 6

On	Off	Off	On	Off	On

4.Turn the power back on to enter the settings into the EEROM and enable the Data Scope Mode.

The On Line light (green) blinks.

5.Turn the power off.

6.Set the DIP switches to the former settings.

DIP switch 1 must be Off to return the printer to the on-line mode.

7.Turn the power back on.

The printer is on-line and can communicate with the host system.

8.Run a transaction from the host system.

All commands and data sent from the host system will be printed as Hex characters as shown in the following illustration.

40

May 1996

Image 45

Contents Owners Guide Information to User Quick Reference How to Use This Book How to Obtain More InformationWho Should Use this Book? Contents Solving Problems Appendix B Print Characteristics 107 About the 7193 Printer Models FeaturesCommunication Interfaces OptionsThermal Printhead Ordering Paper and Supplies Ordering Thermal PaperRecommended Suppliers Kanzaki Specialty Papers Other Qualified SuppliersOrdering the Power Supply and Cables Ordering the Printer Wall-Mount KitOrdering Cash Drawers Cleaning the Printer Removing the Packing Material What Is in the Box?Repacking the Printer Choosing a Location Setting Switches Owner’s Guide Attaching the Feet Connecting Cash Drawer Cables RS-232C Models Connecting Communication and Power CablesParallel Models Turning On the Printer Loading and Changing Paper When to Change the PaperRemoving the Paper Roll Putting In the Paper Roll Advancing Paper Testing the Printer 3cx39pi Mounting the Printer on a Wall Bracket Mounting the Power Supply on a Wall Holder Operator Panel Lights Solving ProblemsCorrecting Problems Service-Related ProblemsOperator-Correctable Conditions Contacting a Service Representative No Power to Printer or Power Voltages IncorrectPrint is Light or Spotty Level 0 Diagnostics DiagnosticsEerom Level 1 DiagnosticsSetting Data Error and Data Buffer options Setting Printhead Resistance Setting Default Lines per Inch Setting Partial Cut Distance Ignoring/Using the Carriage Return Enter the Data Scope Mode Running the Data Scope Mode1BH Exit the Data Scope ModeTesting Receipt Printing Level 3 Diagnostics Level 2 DiagnosticsSending Commands Communication OverviewInterfaces Using DOS to Send Commands Using Basic to Send CommandsRS-232C Interface DTR/DSR Protocol XON/XOFF ProtocolConnectors RS-232C Technical SpecificationsCash Drawer Connectors Switch Settings OFF Parallel Protocol Parallel InterfaceParallel Connectors Parallel Technical SpecificationsParallel Printers Parallel Switch Settings Command List CommandsPrinter Function Commands Owner’s Guide Print Characteristics Commands Printer Status Commands Graphics CommandsBar Code Commands Real Time CommandsCommand Descriptions Horizontal TabLine Feed Carriage Return Clear PrinterFeed n Print Lines Feed n Dot Rows Add n Extra Dot RowsPrint Partial Knife Cut Full Knife CutGenerate Tone Set ColumnSet Absolute Starting Position Set Character Right-Side SpacingSet Line Spacing to n Minimum Units Set Line Spacing to 1/6 InchSelect Printer Initialize PrinterPrint and Feed n Minimum Units Set Horizontal Tab PositionsSet Relative Starting Position Align Character Positions Enable or Disable Panel SwitchSelect Sensors to Stop Printing Print and Feed n LinesRead from Non-Volatile Memory Generate Pulse to Open Cash DrawerWrite to Non-Volatile Memory Select Double-Wide Characters Select Single-Wide CharactersRotate Characters Counter-Clockwise Select Pitch Column Width Set Print ModeDefine User-Defined Character Set Select Character SetSelect Character Code Table Copy Character Set from ROM to RAMSet or Cancel Upside-Down Characters Set or Cancel Rotated Characters ClockwiseSummary of Rotated Printing Set Bit Image Mode N1 + 256 x n2 N1 + 256 x n2 Number of Bytes of Data Double-Density Graphics Single-Density GraphicsDefine Downloaded Bit Image Print Downloaded Bit Image Transmit Cash Drawer Status Request Alternate Status Transmit Printer Status First Implementation Alternate Implementation Rules for Using Real Time CommandsMoving Data Through the Buffer Busy Line and Fault Conditions GS Sequence Real Time Status Transmission= Transmit Printer Status = Transmit RS-232C Busy Status = Transmit Receipt Paper Status Real Time Request to PrinterDLE Sequence Real Time Printer Status Transmission Clear Printer CommandRecognizing Data from the Printer Select Printing Position of HRI Characters Select Pitch of HRI CharactersSelect Height of Bar Code JAN8 EAN Print Bar CodeSelect Width of Bar Code Print Code 128 Bar CodeReliability Appendix a SpecificationsEnvironmental Conditions Power RequirementsPrinting Specifications Dimensions and WeightPrint Zones Duty Cycle Restrictions Printing Solid Blocks Density of Receipt Print LinesAppendix B Print Characteristics Appendix B Print Characteristics Owner’s Guide 110 May May Index Index112 Owner’s Guide Owner’s Guide 114 Owner’s Guide Owner’s Guide Axiohm IPB