Olitec RW400SG manual 4 Login Windows, 5 Quick Setup, 6 Choose WAN Connection Type

Page 12

Figure 4-4 Login Windows

Figure 4-4 Login Windows

Note: If the above screen does not prompt, it means that your web-browser has been set to a proxy. Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it.

If the User Name and Password are correct, you can configure the router using the web browser. Please click the Quick Setup link on the left of the main menu and the Quick Setup screen will appear.

Figure 4-5 Quick Setup

Click Next, the Choose WAN Connection Type page will appear, shown in figure 4-6.

Figure 4-6 Choose WAN Connection Type

The router supports three popular ways to connect to Internet. Please select one compatible with your ISP. Click Next to enter the necessary network parameters.

If you choose "PPPoE", you will see this page shown in figure 4-7:

- 8 -

Image 12

Contents RW400SG Router OLITEC Users GuidePage 5.6.1 DHCP Settings 5.11.3 Factory Defaults Appendix A FAQAppendix B Configuring the PCs Appendix C Specifications2.2 Features Chapter 2 Introduction2.1 Overview of the Router 2.3 Panel Layout 2.3.1 The Front Panel2.3.2 The Rear Panel Chapter 3 Connecting the Router 3.2 Installation Environment Requirements3.3 Connecting the Router 3.1 System RequirementsSwitch/Hub （XDSL 、Cable 、Ethernet ）To LAN To WANChapter 4 Quick Installation Guide 4.1 TCP/IP configuration4.2 Quick Installation Guide Figure 4-4 Login Windows Figure 4-5 Quick SetupFigure 4-6 Choose WAN Connection Type If you choose PPPoE, you will see this page shown in figureFigure 4-7 Quick Setup - PPPoE In this page, you can configure the following wireless parameters Chapter 5 Configuring the Router 5.1 login2. Wireless Radio, SSID, Channel, Mode, Wireless MAC address and IP address5.3 Quick Setup 5.4 NetworkPlease refer to Section 4.2 Quick Installation Guide Figure 5-1 Router Status5.4.1 LAN 5.4.2 WANFigure 5-4 WAN - Dynamic IP Click Logout button to end 802.1x authentication Figure 5-4a WAN - 802.1X + Dynamic IPFigure 5-5 WAN - Static IP You should type the following parameters into the spaces providedClick Login to start 802.1x authentication Click Logout to end 802.1x authenticationFigure 5-5a WAN - 802.1X + Static IP Figure 5-6 WAN - PPPoEFigure 5-7 PPPoE Advanced Settings 5.4.3 MAC Clone 5.5 Wireless 5.5.1 Wireless Settings¾ Mode - Select the desired wireless mode. The options are Encryptions 5.5.2 MAC Filtering Figure 5-12 Add or Modify Wireless MAC Address Filtering entry 5.5.3 Wireless Statistics 5.6.1 DHCP Settings 5.6 DHCP5.6.2 DHCP Clients List 5.6.3 Address Reservation To Reserve IP addressesTo modify A Reserved IP address To delete all Reserved IP addresses5.7 Forwarding 5.7.1 Virtual ServersTo setup a virtual server entry To delete a service entryTo delete all service entries To modify a virtual server entryFigure 5-20 Port Triggering Once configured, operation is as follows Modifying an existing rule Deleting an existing ruleTo delete all rules 5.7.3 DMZ5.7.4 UPnP 5.8 Security 5.8.1 Firewall5.8.2 IP Address Filtering 5.8.3 Domain Filtering Click the Enabled All button to make all entries enabled Figure 5-27 Domain FilteringFigure 5-28 Add or Modify a Domain Filtering entry To add or modify a Domain Filtering entry, follow these instructions5.8.4 MAC Filtering 5.8.5 Remote Management 5.8.6 Advanced Security Click the Save button to save the settings 5.9 Static Routing To add static routing entriesTo modify an existing entry 1. Modify the entry’s Destination IP Address, Subnet Mask and Gateway5.10 DDNS To delete all the entries5.10.1 Dyndns.org DDNS 5.10.2 Oray.net DDNS5.10.3 Comexe.cn DDNS 5.11 System Tools 5.11.1 Time 5.11.2 Firmware5.11.3 Factory Defaults 5.11.4 Reboot5.11.5 Password 5.11.6 Log 5.11.7 StatisticsStatistics Table Click the Refresh button to refresh immediately The total amount of packets received and transmitted by the routerAppendix A FAQ 1. How do I configure the router to access Internet by ADSL users?3. I want to use Netmeeting, what do I need to do? 4. I want to build a WEB Server on the LAN, what should I do? 5. The wireless stations cannot connect to the router Appendix B Configuring the PCs 1. Install TCP/IP component2. Configure TCP/IP for your computer Assigned by DHCP Sever Setting IP address manually Figure B-6 DNS Configuration tabFigure B-5 Gateway tab Figure B-7 IP Address tab Figure B-8 Gateway tabclick Add button. Shown below Figure B-9 DNS Configuration tab Appendix C Specifications GeneralAppendix D Glossary ¾ Domain Name - A descriptive name for an address or group of addresses on the Internet