Olitec RW400SG manual 5a WAN - 802.1X + Static IP, Click Login to start 802.1x authentication

Page 20

Figure 5-5a: WAN - 802.1X + Static IP

If you are also given a user name and a password for 802.1x authentication, you should select 802.1x + Static IP for WAN Connection Type, a box will then appear requesting a user name and a password, shown in figure 5-5a:

Figure 5-5a: WAN - 802.1X + Static IP

¾User Name - Enter the user name for 802.1x authentication provided by your ISP

¾Password - Enter the password for 802.1x authentication provided by your ISP.

Click Login to start 802.1x authentication.

Click Logout to end 802.1x authentication.

3.If you choose PPPoE, you should enter the following parameters (figure 5-6):

Figure 5-6: WAN - PPPoE

¾User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive.

¾Connect on Demand - You can configure the router to disconnect your Internet connection after a specified period of inactivity (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio button. If you want your Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet connection terminates.

-16 -

Image 20

Contents RW400SG Router OLITEC Users GuidePage 5.6.1 DHCP Settings 5.11.3 Factory Defaults Appendix A FAQAppendix B Configuring the PCs Appendix C Specifications2.1 Overview of the Router 2.2 FeaturesChapter 2 Introduction 2.3 Panel Layout 2.3.1 The Front Panel2.3.2 The Rear Panel Chapter 3 Connecting the Router 3.2 Installation Environment Requirements3.3 Connecting the Router 3.1 System RequirementsSwitch/Hub （XDSL 、Cable 、Ethernet ）To LAN To WANChapter 4 Quick Installation Guide 4.1 TCP/IP configuration4.2 Quick Installation Guide Figure 4-4 Login Windows Figure 4-5 Quick SetupFigure 4-6 Choose WAN Connection Type If you choose PPPoE, you will see this page shown in figureFigure 4-7 Quick Setup - PPPoE In this page, you can configure the following wireless parameters Chapter 5 Configuring the Router 5.1 login2. Wireless Radio, SSID, Channel, Mode, Wireless MAC address and IP address5.3 Quick Setup 5.4 NetworkPlease refer to Section 4.2 Quick Installation Guide Figure 5-1 Router Status5.4.1 LAN 5.4.2 WANFigure 5-4 WAN - Dynamic IP Click Logout button to end 802.1x authentication Figure 5-4a WAN - 802.1X + Dynamic IPFigure 5-5 WAN - Static IP You should type the following parameters into the spaces providedClick Login to start 802.1x authentication Click Logout to end 802.1x authenticationFigure 5-5a WAN - 802.1X + Static IP Figure 5-6 WAN - PPPoEFigure 5-7 PPPoE Advanced Settings 5.4.3 MAC Clone 5.5 Wireless 5.5.1 Wireless Settings¾ Mode - Select the desired wireless mode. The options are Encryptions 5.5.2 MAC Filtering Figure 5-12 Add or Modify Wireless MAC Address Filtering entry 5.5.3 Wireless Statistics 5.6.1 DHCP Settings 5.6 DHCP5.6.2 DHCP Clients List 5.6.3 Address Reservation To Reserve IP addressesTo modify A Reserved IP address To delete all Reserved IP addresses5.7 Forwarding 5.7.1 Virtual ServersTo setup a virtual server entry To delete a service entryTo delete all service entries To modify a virtual server entryFigure 5-20 Port Triggering Once configured, operation is as follows Modifying an existing rule Deleting an existing ruleTo delete all rules 5.7.3 DMZ5.7.4 UPnP 5.8 Security 5.8.1 Firewall5.8.2 IP Address Filtering 5.8.3 Domain Filtering Click the Enabled All button to make all entries enabled Figure 5-27 Domain FilteringFigure 5-28 Add or Modify a Domain Filtering entry To add or modify a Domain Filtering entry, follow these instructions5.8.4 MAC Filtering 5.8.5 Remote Management 5.8.6 Advanced Security Click the Save button to save the settings 5.9 Static Routing To add static routing entriesTo modify an existing entry 1. Modify the entry’s Destination IP Address, Subnet Mask and Gateway5.10 DDNS To delete all the entries5.10.1 Dyndns.org DDNS 5.10.2 Oray.net DDNS5.10.3 Comexe.cn DDNS 5.11 System Tools 5.11.1 Time 5.11.2 Firmware5.11.3 Factory Defaults 5.11.4 Reboot5.11.5 Password Statistics Table 5.11.6 Log5.11.7 Statistics Click the Refresh button to refresh immediately The total amount of packets received and transmitted by the routerAppendix A FAQ 1. How do I configure the router to access Internet by ADSL users?3. I want to use Netmeeting, what do I need to do? 4. I want to build a WEB Server on the LAN, what should I do? 5. The wireless stations cannot connect to the router 2. Configure TCP/IP for your computer Appendix B Configuring the PCs1. Install TCP/IP component Assigned by DHCP Sever Figure B-5 Gateway tab Setting IP address manuallyFigure B-6 DNS Configuration tab Figure B-7 IP Address tab Figure B-8 Gateway tabclick Add button. Shown below Figure B-9 DNS Configuration tab Appendix C Specifications GeneralAppendix D Glossary ¾ Domain Name - A descriptive name for an address or group of addresses on the Internet