Olitec RW400SG manual Time, Firmware

Page 49

5.11.1 Time

5.11.1 Time

You can set time manually or get GMT from the Internet for the router on this page (shown in figure 5-39):

Figure 5-39: Time settings

¾Time Zone - Select your local time zone from this pull down list.

¾Date - Enter your local date in MM/DD/YY into the right blanks.

¾Time - Enter your local time in HH/MM/SS into the right blanks.

Time setting follows these steps below:

1.Select your local time zone.

2.Enter date and time in the right blanks

3.Click Save.

Click the Get GMT button to get GMT time from Internet if you have connected to Internet.

Note:

1.This setting will be used for some time-based functions such as firewall. You must specify your time zone once you login to the router successfully, if not the time limited on these functions will not take effect.

2.The time will be lost if the router is turned off.

3.The router will obtain GMT automatically from Internet if it has already connected to Internet.

5.11.2 Firmware

The page (shown in figure 5-40) allows you to upgrade the latest version of firmware for the router.

Figure 5-40: Firmware Upgrade

- 45 -

Image 49

Contents Users Guide RW400SG Router OLITECPage 5.6.1 DHCP Settings Appendix A FAQ 5.11.3 Factory DefaultsAppendix B Configuring the PCs Appendix C SpecificationsChapter 2 Introduction 2.2 Features2.1 Overview of the Router 2.3.1 The Front Panel 2.3 Panel Layout2.3.2 The Rear Panel 3.2 Installation Environment Requirements Chapter 3 Connecting the Router3.3 Connecting the Router 3.1 System Requirements（XDSL 、Cable 、Ethernet ） Switch/HubTo LAN To WAN4.1 TCP/IP configuration Chapter 4 Quick Installation Guide4.2 Quick Installation Guide Figure 4-5 Quick Setup Figure 4-4 Login WindowsFigure 4-6 Choose WAN Connection Type If you choose PPPoE, you will see this page shown in figureFigure 4-7 Quick Setup - PPPoE In this page, you can configure the following wireless parameters 5.1 login Chapter 5 Configuring the Router2. Wireless Radio, SSID, Channel, Mode, Wireless MAC address and IP address5.4 Network 5.3 Quick SetupPlease refer to Section 4.2 Quick Installation Guide Figure 5-1 Router Status5.4.2 WAN 5.4.1 LANFigure 5-4 WAN - Dynamic IP Figure 5-4a WAN - 802.1X + Dynamic IP Click Logout button to end 802.1x authenticationFigure 5-5 WAN - Static IP You should type the following parameters into the spaces providedClick Logout to end 802.1x authentication Click Login to start 802.1x authenticationFigure 5-5a WAN - 802.1X + Static IP Figure 5-6 WAN - PPPoEFigure 5-7 PPPoE Advanced Settings 5.4.3 MAC Clone 5.5.1 Wireless Settings 5.5 Wireless¾ Mode - Select the desired wireless mode. The options are Encryptions 5.5.2 MAC Filtering Figure 5-12 Add or Modify Wireless MAC Address Filtering entry 5.5.3 Wireless Statistics 5.6 DHCP 5.6.1 DHCP Settings5.6.2 DHCP Clients List To Reserve IP addresses 5.6.3 Address ReservationTo modify A Reserved IP address To delete all Reserved IP addresses5.7.1 Virtual Servers 5.7 ForwardingTo delete a service entry To setup a virtual server entryTo delete all service entries To modify a virtual server entryFigure 5-20 Port Triggering Once configured, operation is as follows Deleting an existing rule Modifying an existing ruleTo delete all rules 5.7.3 DMZ5.7.4 UPnP 5.8.1 Firewall 5.8 Security5.8.2 IP Address Filtering 5.8.3 Domain Filtering Figure 5-27 Domain Filtering Click the Enabled All button to make all entries enabledFigure 5-28 Add or Modify a Domain Filtering entry To add or modify a Domain Filtering entry, follow these instructions5.8.4 MAC Filtering 5.8.5 Remote Management 5.8.6 Advanced Security Click the Save button to save the settings To add static routing entries 5.9 Static RoutingTo modify an existing entry 1. Modify the entry’s Destination IP Address, Subnet Mask and GatewayTo delete all the entries 5.10 DDNS5.10.1 Dyndns.org DDNS 5.10.2 Oray.net DDNS5.10.3 Comexe.cn DDNS 5.11 System Tools 5.11.2 Firmware 5.11.1 Time5.11.4 Reboot 5.11.3 Factory Defaults5.11.5 Password 5.11.7 Statistics 5.11.6 LogStatistics Table The total amount of packets received and transmitted by the router Click the Refresh button to refresh immediately1. How do I configure the router to access Internet by ADSL users? Appendix A FAQ3. I want to use Netmeeting, what do I need to do? 4. I want to build a WEB Server on the LAN, what should I do? 5. The wireless stations cannot connect to the router 1. Install TCP/IP component Appendix B Configuring the PCs2. Configure TCP/IP for your computer Assigned by DHCP Sever Figure B-6 DNS Configuration tab Setting IP address manuallyFigure B-5 Gateway tab Figure B-8 Gateway tab Figure B-7 IP Address tabclick Add button. Shown below Figure B-9 DNS Configuration tab General Appendix C SpecificationsAppendix D Glossary ¾ Domain Name - A descriptive name for an address or group of addresses on the Internet