Olitec RW400SG manual 7 Quick Setup - PPPoE

Page 13

Figure 4-7 Quick Setup - PPPoE

Figure 4-7 Quick Setup - PPPoE

¾User Name and Password - Enter the User Name and Password provided by your ISP. These fields are case sensitive. If you have difficulty with this process, please contact your ISP.

If you choose " Dynamic IP", the router will automatically receive the IP parameters from your ISP without needing to enter any parameters.

If you Choose "Static IP", the Static IP settings page will appear, shown in figure 4-8:

Figure 4-8 Quick Setup - Static IP

Note: The IP parameters should have been provided by your ISP.

¾IP Address - This is the WAN IP address as seen by external users on the Internet (including your ISP). Enter the IP address into the field.

¾Subnet Mask - The Subnet Mask is used for the WAN IP address, it is usually 255.255.255.0

¾Default Gateway - Enter the gateway into the box if required.

¾Primary DNS - Enter the DNS Server IP address into the boxes if required.

¾Secondary DNS - If your ISP provides another DNS server, enter it into this field.

After you complete the above, click Next, the Wireless settings page will appear, shown in figure 4-9.

Figure 4-9 Quick Setup - Wireless settings

- 9 -

Image 13

Contents Users Guide RW400SG Router OLITECPage 5.6.1 DHCP Settings Appendix A FAQ 5.11.3 Factory DefaultsAppendix B Configuring the PCs Appendix C SpecificationsChapter 2 Introduction 2.2 Features2.1 Overview of the Router 2.3.1 The Front Panel 2.3 Panel Layout2.3.2 The Rear Panel 3.2 Installation Environment Requirements Chapter 3 Connecting the Router3.3 Connecting the Router 3.1 System Requirements（XDSL 、Cable 、Ethernet ） Switch/HubTo LAN To WAN4.1 TCP/IP configuration Chapter 4 Quick Installation Guide4.2 Quick Installation Guide Figure 4-5 Quick Setup Figure 4-4 Login WindowsFigure 4-6 Choose WAN Connection Type If you choose PPPoE, you will see this page shown in figureFigure 4-7 Quick Setup - PPPoE In this page, you can configure the following wireless parameters 5.1 login Chapter 5 Configuring the Router2. Wireless Radio, SSID, Channel, Mode, Wireless MAC address and IP address5.4 Network 5.3 Quick SetupPlease refer to Section 4.2 Quick Installation Guide Figure 5-1 Router Status5.4.2 WAN 5.4.1 LANFigure 5-4 WAN - Dynamic IP Figure 5-4a WAN - 802.1X + Dynamic IP Click Logout button to end 802.1x authenticationFigure 5-5 WAN - Static IP You should type the following parameters into the spaces providedClick Logout to end 802.1x authentication Click Login to start 802.1x authenticationFigure 5-5a WAN - 802.1X + Static IP Figure 5-6 WAN - PPPoEFigure 5-7 PPPoE Advanced Settings 5.4.3 MAC Clone 5.5.1 Wireless Settings 5.5 Wireless¾ Mode - Select the desired wireless mode. The options are Encryptions 5.5.2 MAC Filtering Figure 5-12 Add or Modify Wireless MAC Address Filtering entry 5.5.3 Wireless Statistics 5.6 DHCP 5.6.1 DHCP Settings5.6.2 DHCP Clients List To Reserve IP addresses 5.6.3 Address ReservationTo modify A Reserved IP address To delete all Reserved IP addresses5.7.1 Virtual Servers 5.7 ForwardingTo delete a service entry To setup a virtual server entryTo delete all service entries To modify a virtual server entryFigure 5-20 Port Triggering Once configured, operation is as follows Deleting an existing rule Modifying an existing ruleTo delete all rules 5.7.3 DMZ5.7.4 UPnP 5.8.1 Firewall 5.8 Security5.8.2 IP Address Filtering 5.8.3 Domain Filtering Figure 5-27 Domain Filtering Click the Enabled All button to make all entries enabledFigure 5-28 Add or Modify a Domain Filtering entry To add or modify a Domain Filtering entry, follow these instructions5.8.4 MAC Filtering 5.8.5 Remote Management 5.8.6 Advanced Security Click the Save button to save the settings To add static routing entries 5.9 Static RoutingTo modify an existing entry 1. Modify the entry’s Destination IP Address, Subnet Mask and GatewayTo delete all the entries 5.10 DDNS5.10.1 Dyndns.org DDNS 5.10.2 Oray.net DDNS5.10.3 Comexe.cn DDNS 5.11 System Tools 5.11.2 Firmware 5.11.1 Time5.11.4 Reboot 5.11.3 Factory Defaults5.11.5 Password 5.11.7 Statistics 5.11.6 LogStatistics Table The total amount of packets received and transmitted by the router Click the Refresh button to refresh immediately1. How do I configure the router to access Internet by ADSL users? Appendix A FAQ3. I want to use Netmeeting, what do I need to do? 4. I want to build a WEB Server on the LAN, what should I do? 5. The wireless stations cannot connect to the router 1. Install TCP/IP component Appendix B Configuring the PCs2. Configure TCP/IP for your computer Assigned by DHCP Sever Figure B-6 DNS Configuration tab Setting IP address manuallyFigure B-5 Gateway tab Figure B-8 Gateway tab Figure B-7 IP Address tabclick Add button. Shown below Figure B-9 DNS Configuration tab General Appendix C SpecificationsAppendix D Glossary ¾ Domain Name - A descriptive name for an address or group of addresses on the Internet