Olitec RW400SG manual Wireless Settings

Page 23
5.5 Wireless

5.5 Wireless

Figure 5-9: Wireless menu

There are three submenus under the Wireless menu (shown in figure 5-9): Wireless Settings, MAC Filtering and Wireless Statistics. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below.

5.5.1 Wireless Settings

The basic settings for the wireless network are set on this page, figure 5-10:

Figure 5-10: Wireless Settings

¾SSID - Enter a value of up to 32 characters. The same name (SSID) must be assigned to all wireless devices in your network. The default SSID is default, but it is recommended strongly that you change your networks name (SSID) to a different value. This value is case-sensitive. For example, DEFAULT is NOT the same as default.

¾Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the router can be used. It may be illegal to use the

-19 -

Image 23
Contents Users Guide RW400SG Router OLITECPage 5.6.1 DHCP Settings Appendix C Specifications 5.11.3 Factory DefaultsAppendix A FAQ Appendix B Configuring the PCs2.1 Overview of the Router 2.2 FeaturesChapter 2 Introduction 2.3.1 The Front Panel 2.3 Panel Layout2.3.2 The Rear Panel 3.1 System Requirements Chapter 3 Connecting the Router3.2 Installation Environment Requirements 3.3 Connecting the RouterTo WAN Switch/Hub(XDSL 、Cable 、Ethernet ) To LAN4.1 TCP/IP configuration Chapter 4 Quick Installation Guide4.2 Quick Installation Guide If you choose PPPoE, you will see this page shown in figure Figure 4-4 Login WindowsFigure 4-5 Quick Setup Figure 4-6 Choose WAN Connection TypeFigure 4-7 Quick Setup - PPPoE In this page, you can configure the following wireless parameters Radio, SSID, Channel, Mode, Wireless MAC address and IP address Chapter 5 Configuring the Router5.1 login 2. WirelessFigure 5-1 Router Status 5.3 Quick Setup5.4 Network Please refer to Section 4.2 Quick Installation Guide5.4.2 WAN 5.4.1 LANFigure 5-4 WAN - Dynamic IP You should type the following parameters into the spaces provided Click Logout button to end 802.1x authenticationFigure 5-4a WAN - 802.1X + Dynamic IP Figure 5-5 WAN - Static IPFigure 5-6 WAN - PPPoE Click Login to start 802.1x authenticationClick Logout to end 802.1x authentication Figure 5-5a WAN - 802.1X + Static IPFigure 5-7 PPPoE Advanced Settings 5.4.3 MAC Clone 5.5.1 Wireless Settings 5.5 Wireless¾ Mode - Select the desired wireless mode. The options are Encryptions 5.5.2 MAC Filtering Figure 5-12 Add or Modify Wireless MAC Address Filtering entry 5.5.3 Wireless Statistics 5.6 DHCP 5.6.1 DHCP Settings5.6.2 DHCP Clients List To delete all Reserved IP addresses 5.6.3 Address ReservationTo Reserve IP addresses To modify A Reserved IP address5.7.1 Virtual Servers 5.7 ForwardingTo modify a virtual server entry To setup a virtual server entryTo delete a service entry To delete all service entriesFigure 5-20 Port Triggering Once configured, operation is as follows 5.7.3 DMZ Modifying an existing ruleDeleting an existing rule To delete all rules5.7.4 UPnP 5.8.1 Firewall 5.8 Security5.8.2 IP Address Filtering 5.8.3 Domain Filtering To add or modify a Domain Filtering entry, follow these instructions Click the Enabled All button to make all entries enabledFigure 5-27 Domain Filtering Figure 5-28 Add or Modify a Domain Filtering entry5.8.4 MAC Filtering 5.8.5 Remote Management 5.8.6 Advanced Security Click the Save button to save the settings 1. Modify the entry’s Destination IP Address, Subnet Mask and Gateway 5.9 Static RoutingTo add static routing entries To modify an existing entry5.10.2 Oray.net DDNS 5.10 DDNSTo delete all the entries 5.10.1 Dyndns.org DDNS5.10.3 Comexe.cn DDNS 5.11 System Tools 5.11.2 Firmware 5.11.1 Time5.11.4 Reboot 5.11.3 Factory Defaults5.11.5 Password Statistics Table 5.11.6 Log5.11.7 Statistics The total amount of packets received and transmitted by the router Click the Refresh button to refresh immediately1. How do I configure the router to access Internet by ADSL users? Appendix A FAQ3. I want to use Netmeeting, what do I need to do? 4. I want to build a WEB Server on the LAN, what should I do? 5. The wireless stations cannot connect to the router 2. Configure TCP/IP for your computer Appendix B Configuring the PCs1. Install TCP/IP component Assigned by DHCP Sever Figure B-5 Gateway tab Setting IP address manuallyFigure B-6 DNS Configuration tab Figure B-8 Gateway tab Figure B-7 IP Address tabclick Add button. Shown below Figure B-9 DNS Configuration tab General Appendix C SpecificationsAppendix D Glossary ¾ Domain Name - A descriptive name for an address or group of addresses on the Internet