Olitec RW400SG manual

Contents RW400SG Router OLITEC Users GuidePage 5.6.1 DHCP Settings Appendix B Configuring the PCs 5.11.3 Factory DefaultsAppendix A FAQ Appendix C Specifications2.1 Overview of the Router 2.2 FeaturesChapter 2 Introduction 2.3 Panel Layout 2.3.1 The Front Panel2.3.2 The Rear Panel 3.3 Connecting the Router Chapter 3 Connecting the Router3.2 Installation Environment Requirements 3.1 System RequirementsTo LAN Switch/Hub（XDSL 、Cable 、Ethernet ） To WANChapter 4 Quick Installation Guide 4.1 TCP/IP configuration4.2 Quick Installation Guide Figure 4-6 Choose WAN Connection Type Figure 4-4 Login WindowsFigure 4-5 Quick Setup If you choose PPPoE, you will see this page shown in figureFigure 4-7 Quick Setup - PPPoE In this page, you can configure the following wireless parameters 2. Wireless Chapter 5 Configuring the Router5.1 login Radio, SSID, Channel, Mode, Wireless MAC address and IP addressPlease refer to Section 4.2 Quick Installation Guide 5.3 Quick Setup5.4 Network Figure 5-1 Router Status5.4.1 LAN 5.4.2 WANFigure 5-4 WAN - Dynamic IP Figure 5-5 WAN - Static IP Click Logout button to end 802.1x authenticationFigure 5-4a WAN - 802.1X + Dynamic IP You should type the following parameters into the spaces providedFigure 5-5a WAN - 802.1X + Static IP Click Login to start 802.1x authenticationClick Logout to end 802.1x authentication Figure 5-6 WAN - PPPoEFigure 5-7 PPPoE Advanced Settings 5.4.3 MAC Clone 5.5 Wireless 5.5.1 Wireless Settings¾ Mode - Select the desired wireless mode. The options are Encryptions 5.5.2 MAC Filtering Figure 5-12 Add or Modify Wireless MAC Address Filtering entry 5.5.3 Wireless Statistics 5.6.1 DHCP Settings 5.6 DHCP5.6.2 DHCP Clients List To modify A Reserved IP address 5.6.3 Address ReservationTo Reserve IP addresses To delete all Reserved IP addresses5.7 Forwarding 5.7.1 Virtual ServersTo delete all service entries To setup a virtual server entryTo delete a service entry To modify a virtual server entryFigure 5-20 Port Triggering Once configured, operation is as follows To delete all rules Modifying an existing ruleDeleting an existing rule 5.7.3 DMZ5.7.4 UPnP 5.8 Security 5.8.1 Firewall5.8.2 IP Address Filtering 5.8.3 Domain Filtering Figure 5-28 Add or Modify a Domain Filtering entry Click the Enabled All button to make all entries enabledFigure 5-27 Domain Filtering To add or modify a Domain Filtering entry, follow these instructions5.8.4 MAC Filtering 5.8.5 Remote Management 5.8.6 Advanced Security Click the Save button to save the settings To modify an existing entry 5.9 Static RoutingTo add static routing entries 1. Modify the entry’s Destination IP Address, Subnet Mask and Gateway5.10.1 Dyndns.org DDNS 5.10 DDNSTo delete all the entries 5.10.2 Oray.net DDNS5.10.3 Comexe.cn DDNS 5.11 System Tools 5.11.1 Time 5.11.2 Firmware5.11.3 Factory Defaults 5.11.4 Reboot5.11.5 Password Statistics Table 5.11.6 Log5.11.7 Statistics Click the Refresh button to refresh immediately The total amount of packets received and transmitted by the routerAppendix A FAQ 1. How do I configure the router to access Internet by ADSL users?3. I want to use Netmeeting, what do I need to do? 4. I want to build a WEB Server on the LAN, what should I do? 5. The wireless stations cannot connect to the router 2. Configure TCP/IP for your computer Appendix B Configuring the PCs1. Install TCP/IP component Assigned by DHCP Sever Figure B-5 Gateway tab Setting IP address manuallyFigure B-6 DNS Configuration tab Figure B-7 IP Address tab Figure B-8 Gateway tabclick Add button. Shown below Figure B-9 DNS Configuration tab Appendix C Specifications GeneralAppendix D Glossary ¾ Domain Name - A descriptive name for an address or group of addresses on the Internet