Olitec RW400SG manual ¾ Mode - Select the desired wireless mode. The options are

Page 24

wireless function of the router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance

Note: Some regions may not use 108Mbps Mode since the operation for the wireless interface in 108Mbps Mode is illegal.

¾Channel - This field determines which operating frequency will be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.

¾Mode - Select the desired wireless mode. The options are:

•108Mbps (Dynamic) - Super GTM, 802.11g and 802.11b wireless stations can connect to the router.

•108Mbps (Static) - Only Super GTM wireless stations can connect to the router.

•54Mbps (802.11g) - Both 802.11g and 802.11b wireless stations can connect to the router.

•11Mbps (802.11b) - Only 802.11b wireless stations can connect to the router. Note: The default is "54Mbps (802.11g)", which allows both 802.11g and 802.11b wireless stations to connect to the router.

¾Enable Wireless Router Radio - The wireless radio of this Router can be enabled or disabled to allow wireless stations access. If enabled, wireless stations will be able to access the router, otherwise, wireless stations will not be able to access the router.

¾Enable SSID Broadcast - If you select the Enable SSID Broadcast checkbox, the Wireless Router SSID will broadcast its name (SSID) on the air.

¾Enable Wireless Security – The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the router without encryption. It is strongly recommended that you choose this optional to encrypt your wireless network. The encryption settings described below.

¾Authentication Type - You can select one of the following authentication types:

•WEP - Select WEP authentication type based on 802.11 authentication.

•WPA-PSK/WPA2-PSK - Select WPA/WPA2 authentication type based on pre-shared passphrase.

•WPA /WPA2 - Select WPA/WPA2 authentication type based on Radius Server.

¾Authentication Option - You can select one of the following authentication options:

•When you select WEP as an authentication type you can select following authentication option:

•Automatic - Select Shared Key or Open System authentication type automatically based on the wireless station request.

•Shared Key - Select 802.11 Shared Key authentication.

•Open System - Select 802.11 Open System authentication.

•When you select WPA-PSK/WPA2-PSKfor authentication type you can select

-20 -

Page 23 Page 25
Image 24
Page 23 Page 25
Contents RW400SG Router OLITEC Users GuidePage 5.6.1 DHCP Settings 5.11.3 Factory Defaults Appendix A FAQAppendix B Configuring the PCs Appendix C Specifications2.2 Features Chapter 2 Introduction2.1 Overview of the Router 2.3 Panel Layout 2.3.1 The Front Panel2.3.2 The Rear Panel Chapter 3 Connecting the Router 3.2 Installation Environment Requirements3.3 Connecting the Router 3.1 System RequirementsSwitch/Hub （XDSL 、Cable 、Ethernet ）To LAN To WANChapter 4 Quick Installation Guide 4.1 TCP/IP configuration4.2 Quick Installation Guide Figure 4-4 Login Windows Figure 4-5 Quick SetupFigure 4-6 Choose WAN Connection Type If you choose PPPoE, you will see this page shown in figureFigure 4-7 Quick Setup - PPPoE In this page, you can configure the following wireless parameters Chapter 5 Configuring the Router 5.1 login2. Wireless Radio, SSID, Channel, Mode, Wireless MAC address and IP address5.3 Quick Setup 5.4 NetworkPlease refer to Section 4.2 Quick Installation Guide Figure 5-1 Router Status5.4.1 LAN 5.4.2 WANFigure 5-4 WAN - Dynamic IP Click Logout button to end 802.1x authentication Figure 5-4a WAN - 802.1X + Dynamic IPFigure 5-5 WAN - Static IP You should type the following parameters into the spaces providedClick Login to start 802.1x authentication Click Logout to end 802.1x authenticationFigure 5-5a WAN - 802.1X + Static IP Figure 5-6 WAN - PPPoEFigure 5-7 PPPoE Advanced Settings 5.4.3 MAC Clone 5.5 Wireless 5.5.1 Wireless Settings¾ Mode - Select the desired wireless mode. The options are Encryptions 5.5.2 MAC Filtering Figure 5-12 Add or Modify Wireless MAC Address Filtering entry 5.5.3 Wireless Statistics 5.6.1 DHCP Settings 5.6 DHCP5.6.2 DHCP Clients List 5.6.3 Address Reservation To Reserve IP addressesTo modify A Reserved IP address To delete all Reserved IP addresses5.7 Forwarding 5.7.1 Virtual ServersTo setup a virtual server entry To delete a service entryTo delete all service entries To modify a virtual server entryFigure 5-20 Port Triggering Once configured, operation is as follows Modifying an existing rule Deleting an existing ruleTo delete all rules 5.7.3 DMZ5.7.4 UPnP 5.8 Security 5.8.1 Firewall5.8.2 IP Address Filtering 5.8.3 Domain Filtering Click the Enabled All button to make all entries enabled Figure 5-27 Domain FilteringFigure 5-28 Add or Modify a Domain Filtering entry To add or modify a Domain Filtering entry, follow these instructions5.8.4 MAC Filtering 5.8.5 Remote Management 5.8.6 Advanced Security Click the Save button to save the settings 5.9 Static Routing To add static routing entriesTo modify an existing entry 1. Modify the entry’s Destination IP Address, Subnet Mask and Gateway5.10 DDNS To delete all the entries5.10.1 Dyndns.org DDNS 5.10.2 Oray.net DDNS5.10.3 Comexe.cn DDNS 5.11 System Tools 5.11.1 Time 5.11.2 Firmware5.11.3 Factory Defaults 5.11.4 Reboot5.11.5 Password 5.11.6 Log 5.11.7 StatisticsStatistics Table Click the Refresh button to refresh immediately The total amount of packets received and transmitted by the routerAppendix A FAQ 1. How do I configure the router to access Internet by ADSL users?3. I want to use Netmeeting, what do I need to do? 4. I want to build a WEB Server on the LAN, what should I do? 5. The wireless stations cannot connect to the router Appendix B Configuring the PCs 1. Install TCP/IP component2. Configure TCP/IP for your computer Assigned by DHCP Sever Setting IP address manually Figure B-6 DNS Configuration tabFigure B-5 Gateway tab Figure B-7 IP Address tab Figure B-8 Gateway tabclick Add button. Shown below Figure B-9 DNS Configuration tab Appendix C Specifications GeneralAppendix D Glossary ¾ Domain Name - A descriptive name for an address or group of addresses on the Internet
Top Page Image Contents