Olitec RW400SG manual Password

Page 51

5.11.5 Password

Figure 5-42: Reboot the router

Click the Reboot button to reboot the router.

Some settings of the router will take effect only after rebooting, which include:

•Change LAN IP Address. (System will reboot automatically)

•MAC Clone (system will reboot automatically)

•DHCP service function.

•Static address assignment of DHCP server.

•Web Service Port of the router.

•Upgrade the firmware of the router (system will reboot automatically).

•Restore the router's settings to factory default (system will reboot automatically).

5.11.5 Password

This page (shown in figure 5-43) allows you to change the factory default user name and password of the router.

Figure 5-43: Password

It is strongly recommended that you change the factory default user name and password of the router. All users who try to access the router's web-based utility or Quick Setup will be prompted for the router's user name and password.

Note: The new user name and password must not exceed 14 characters in length and must not include any spaces. Enter the new Password twice to confirm it.

Click the Save button when finished. Click the Clear All button to clear all.

- 47 -

Image 51

Contents Users Guide RW400SG Router OLITECPage 5.6.1 DHCP Settings Appendix C Specifications 5.11.3 Factory DefaultsAppendix A FAQ Appendix B Configuring the PCs2.2 Features Chapter 2 Introduction2.1 Overview of the Router 2.3.1 The Front Panel 2.3 Panel Layout2.3.2 The Rear Panel 3.1 System Requirements Chapter 3 Connecting the Router3.2 Installation Environment Requirements 3.3 Connecting the RouterTo WAN Switch/Hub（XDSL 、Cable 、Ethernet ） To LAN4.1 TCP/IP configuration Chapter 4 Quick Installation Guide4.2 Quick Installation Guide If you choose PPPoE, you will see this page shown in figure Figure 4-4 Login WindowsFigure 4-5 Quick Setup Figure 4-6 Choose WAN Connection TypeFigure 4-7 Quick Setup - PPPoE In this page, you can configure the following wireless parameters Radio, SSID, Channel, Mode, Wireless MAC address and IP address Chapter 5 Configuring the Router5.1 login 2. WirelessFigure 5-1 Router Status 5.3 Quick Setup5.4 Network Please refer to Section 4.2 Quick Installation Guide5.4.2 WAN 5.4.1 LANFigure 5-4 WAN - Dynamic IP You should type the following parameters into the spaces provided Click Logout button to end 802.1x authenticationFigure 5-4a WAN - 802.1X + Dynamic IP Figure 5-5 WAN - Static IPFigure 5-6 WAN - PPPoE Click Login to start 802.1x authenticationClick Logout to end 802.1x authentication Figure 5-5a WAN - 802.1X + Static IPFigure 5-7 PPPoE Advanced Settings 5.4.3 MAC Clone 5.5.1 Wireless Settings 5.5 Wireless¾ Mode - Select the desired wireless mode. The options are Encryptions 5.5.2 MAC Filtering Figure 5-12 Add or Modify Wireless MAC Address Filtering entry 5.5.3 Wireless Statistics 5.6 DHCP 5.6.1 DHCP Settings5.6.2 DHCP Clients List To delete all Reserved IP addresses 5.6.3 Address ReservationTo Reserve IP addresses To modify A Reserved IP address5.7.1 Virtual Servers 5.7 ForwardingTo modify a virtual server entry To setup a virtual server entryTo delete a service entry To delete all service entriesFigure 5-20 Port Triggering Once configured, operation is as follows 5.7.3 DMZ Modifying an existing ruleDeleting an existing rule To delete all rules5.7.4 UPnP 5.8.1 Firewall 5.8 Security5.8.2 IP Address Filtering 5.8.3 Domain Filtering To add or modify a Domain Filtering entry, follow these instructions Click the Enabled All button to make all entries enabledFigure 5-27 Domain Filtering Figure 5-28 Add or Modify a Domain Filtering entry5.8.4 MAC Filtering 5.8.5 Remote Management 5.8.6 Advanced Security Click the Save button to save the settings 1. Modify the entry’s Destination IP Address, Subnet Mask and Gateway 5.9 Static RoutingTo add static routing entries To modify an existing entry5.10.2 Oray.net DDNS 5.10 DDNSTo delete all the entries 5.10.1 Dyndns.org DDNS5.10.3 Comexe.cn DDNS 5.11 System Tools 5.11.2 Firmware 5.11.1 Time5.11.4 Reboot 5.11.3 Factory Defaults5.11.5 Password 5.11.6 Log 5.11.7 StatisticsStatistics Table The total amount of packets received and transmitted by the router Click the Refresh button to refresh immediately1. How do I configure the router to access Internet by ADSL users? Appendix A FAQ3. I want to use Netmeeting, what do I need to do? 4. I want to build a WEB Server on the LAN, what should I do? 5. The wireless stations cannot connect to the router Appendix B Configuring the PCs 1. Install TCP/IP component2. Configure TCP/IP for your computer Assigned by DHCP Sever Setting IP address manually Figure B-6 DNS Configuration tabFigure B-5 Gateway tab Figure B-8 Gateway tab Figure B-7 IP Address tabclick Add button. Shown below Figure B-9 DNS Configuration tab General Appendix C SpecificationsAppendix D Glossary ¾ Domain Name - A descriptive name for an address or group of addresses on the Internet