SSI America EPS2U Control and Indicator Functions, Pson#, Pson # = Low Pson # = Open or High

Page 26

SSI

EPS2U Power Supply Design Guide, V2.1

8Control and Indicator Functions

The following sections define the input and output signals from the power supply. Signals that can be defined as low true use the following convention:

signal# = low true

8.1PSON#

STATUS

Required

The PSON# signal is required to remotely turn on/off the power supply. PSON# is an active low signal that turns on the +3.3 V, +5 V, +12 V, and -12 V power rails. When this signal is not pulled low by the system, or left open, the outputs (except the +5 VSB and Vbias) turn off. This signal is pulled to a standby voltage by a pull-up resistor internal to the power supply. Refer to Figure 3 for timing diagram.

 

Table 28: PSON# Signal Characteristic

 

 

Signal Type

 

Accepts an open collector/drain input from the system.

 

Pull-up to VSB located in power supply.

 

 

 

 

 

 

 

PSON# = Low

 

 

ON

PSON# = Open or High

 

OFF

 

 

MIN

 

MAX

Logic level low (power supply ON)

0 V

 

1.0 V

 

 

 

Logic level high (power supply OFF)

2.0 V

 

5.25 V

 

 

 

Source current, Vpson = low

 

 

4 mA

 

 

 

Power up delay:

Tpson_on_delay

5 ms

 

400 ms

 

 

 

PWOK delay:

T pson_pwok

 

 

50 ms

 

 

 

Disabled

Enabled

Hysteresis ≥ 0.3V and/or other de-bounce method

≤ 1.0 V

≥ 2.0 V

PS is

PS is

enabled

disabled

0V

1.0V

2.0V

5.25V

Figure 4: PSON# Signal Characteristics

- 26 -

Image 26
Contents SSI Disclaimer Contents Figures TablesPurpose Conceptual OverviewDefinitions/Terms/Acronyms RequiredMechanical Overview Required OptionalRecommended Temperature RequirementsAirflow Requirements Thermal RequirementsAC Input Requirements AC Inlet ConnectorAC Input Voltage Specification EfficiencyAC Line Fuse AC Line Transient SpecificationAC Line Dropout AC InrushAC Line Surge Transient Performance AC Line Fast Transient SpecificationAC Line Sag Transient Performance AC Line Surge1 12V Power Rail Configurations DC Output SpecificationOutput Connectors 12V Rail SummaryPin Signal AWG Color Baseboard power connectorP1 Baseboard Power Connector Common Plane P1 Baseboard Power Connector Split PlaneProcessor Power Connector Split Plane Processor Power ConnectorProcessor Power Connector Common Plane Server Signal Connector Peripheral Power ConnectorsFloppy Power Connector Peripheral Power ConnectorsRemote Sense Server Signal ConnectorGrounding Voltage Minimum Continuous Maximum Continuous Peak Output Power/Currents480 W Load Ratings Common Plane 550 W Load Ratings Split Plane650 W Load Ratings Split Plane Standby Outputs600 W Load Ratings Split Plane Parameter Voltage RegulationVoltage Regulation Limits Units ToleranceTransient Load Requirements Dynamic LoadingCapacitive Loading Capacitve Loading ConditionsRipple and Noise Ripple / NoiseTiming Requirements Output Voltage TimingOutput Voltage Timing Turn On/Off Timing Turn On/Off Timing Single Power Supply Recommended Description240VA Protection Protection CircuitsCurrent Limit Over Current ProtectionOver Voltage Limits Over Temperature ProtectionOver Voltage Protection Output VoltagePwok delay Control and Indicator FunctionsPson # Signal Characteristic Signal Type PSON#Pwok Signal Characteristics Pwok Power OKField Replacement Unit FRU Signals FRU DataFRU Device Information FRU Data FormatProduct Info Area FRU Device Product Information AreaMultiRecord Area Field Name PS Info Field Information DefinitionMtbf Agency Requirements