Teac P-55 instruction manual Indicating Operation State, Preheating heatroller

Page 19

SECTION 9 : Control Panel Features

Indicating Operation State

BUSY: shows the printer is in operation.

While colors are being printed on the transfer ribbon, the following messages are displayed on the LCD. (The LCD displays the messages as shown below with PHOTO ink installed. With COLOR ink installed, the printer prints black, cyan, magenta, and then yellow.)

B U

S

Y

Ο

P r

i

n t i n g

B l a c k

 

 

 

 

 

 

 

 

B U

S

Y

Ο

P r

i

n t i n g

Y e l l o w

 

 

 

 

 

 

 

 

B U

S

Y

Ο

P r

i

n t i n g

M a g e n t a

 

 

 

 

 

 

 

 

B U

S

Y

Ο

P r

i

n t i n g

C y a n

 

 

 

 

 

 

 

 

B U

S

Y

Ο

D i

s

c T r a n s f e r

The above message is displayed while the image printed on the transfer ribbon is being transferred to a medium.

Busy is also displayed for operations other than printing [Preprocessing image to be printed]

B

U S

Y

Ο

I

m a

g

e C a l c u l

a t e

 

 

 

 

[Preheating heatroller]

 

 

 

 

B

U S Y

Ο

A

d j

u

s t i n g T e

m p

 

 

 

 

 

*The above message is displayed and no other operations are performed until the heatroller reaches the specified temperature.

When the temperature gets high enough, the printer starts a transfer operation.

[Cooling thermal printhead]

B U

S

Y

Ο

H e

a

d C o o l

D o w n

*As the printhead exceeds a certain temperature, the P-55 stops print-related operations indicating the above message. The P-55 is automatically return to operation as the printhead goes down to the right temperature.

When a print medium is loaded, a circle ( ) is displayed in the upper right corner of the LCD display.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Disc Label Printer Table of Contents Important Safety Instructions Important Safety Instructions Introduction FeaturesBlank media CD-R 10-pack of discs Printer cable Unpacking and InspectionExhaust Fan on the right side Identifying the PartsStatus AUX Connector optional Choosing Adequate Location Choosing Adequate Location Installing/Removing Shipping Protection Materials Setting the Parallel Interface Mode on the PC Setup Installing the Label EditorInstalling the Label Editor Connections Connecting PC to P-55A C Control Panel Features L e c t Selecting USB / Parallel PortPreheating heatroller Indicating Operation StateWindow Please wait while the wizard installs Installing the Printer DriverStandard Mode Error Message Description Corrective Action Error Messages ExplainedFor the contact details, see Contact If the shaft is erroneously protruding, place the ribbon Check the shaft flange Loading Ribbons How to Load a RibbonLoading Ink Ribbon Loading Ribbons Loading Re-transfer Ribbon Turn the take-up shaft clockwise to take up ribbon slack Loading Ribbons Checking the Remaining Ribbon Amount Loading Print Media Guide PinsGetting Label Print Job Started Getting Label Print Job StartedGetting Label Print Job Started Click OK When the process is completed, the tray slides out Supplementary explanation Print to fileCorrecting for displacement Correcting for displacement and hue shift between colorsClick Repeat on the Maintenance tab Getting Label Print Job Started Correcting for hue shift between colors Correcting for aspect ratio Getting Label Print Job Started Beware Removing Disc Label Editor and Printer Driver Point to Start, Settings and then PrintersSelect File and then Server Properties Removing Disc Label Editor and Printer Driver Select Add or Remove Programs Removing Disc Label Editor and Printer Driver Uninstalling the P-55 related information Maintenance Periodic Checks and Maintenance by Service Personnel Cleaning the cooling fan filter every half yearRibbon set ShippingPrinter SpecificationsGeneral External Dimensions Options Product Information Teac America, Inc Contact InformationTechnical Support Teac America, Inc. Dspd Technical Support
Top Page Image Contents