Varec 8315 Series manual ID DIP Switch SW1, LED Indicators D1-D6

Page 27

8300	8315 L&J Tankway Interface Module

Figure 3-3: Model 8315 L&J Tankway Interface

ID DIP Switch (SW1)

LED indicators (D1 D6)

+48-65 VDC power fuse

(1 A 250V TR5) (F1)

External Power Connector

(+48 - 65 VDC) (J2)

Field wiring

terminal block (J3)

Surge/Shield

ground connector (J4)

Transmit Line Fuse

(63 mA 250V TR5) (F2)

3.2.1ID DIP Switch (SW1)

The ID DIP Switch is a binary switch that sets the unit ID number (1-4). This value is set to the port number on which the Model 8315 is installed (e.g. P1=1). The switch is set according to its location on the motherboard. Set to “1” for P1, “2” for P2, “3” for P3, and “4” for P4. Refer to the following figures:

Figure 3-4: ID DIP Switch settings

3.2.2LED Indicators (D1-D6)

The LED displays indicate the status of the Model 8315’s CPU and communications. The indicators are identified in the following figure.

•CPU: CPU activity

17

Image 27

Contents Installation Operations Manual Page Copyright Disclaimer of Warranties Safety Precaution Definitions Safety Precautions Overview InstallationUsing ViewRTU Troubleshooting and maintenanceContents System Information SYS Using ViewRTU Troubleshooting Features VersionsApplications Operating temperature Specifications System DesignPower Supply Power consumptionStorage temperature HumidityMechanical Construction Overview TankGate Interface Hardware Motherboard Description Hardware Block DiagramTankGate motherboard Surge Protection Surge Gnd terminal block J4 Unit AC Input Power terminal block J2Field Power Vfield terminal block J3 Auxiliary DC Output Power terminal block J8Field Voltage Selection Jumper W3 AC Power Fuses F1,F2Switches and Indicators Reset push-button SW3Hard Reset 3.1 COM0 J7 Communications3.3 COM1 RS232/RS-485 Selection Switch SW2 3.4 COM1 Hardware Handshaking Switch SW13.2 COM1 RS-232/RS-485 J5 SW2 Set Tion Physical Handshak Ting Layer Ing Communica HardwareWith RTS / CTS RS-232J6 TankGate Communications Cable8315 L&J Tankway Interface Module Model 8315 TankGate DescriptionLED Indicators D1-D6 ID DIP Switch SW1Surge/Shield Ground Connector J4 External Power Connector +48V J2Connect the field wiring Field Wiring terminal block J38315 L&J Tankway Interface Module TankGate Interface Software Features Real-Time / Multitasking Executive Automatic Fault RecoveryReal-Time Clock System Tasks ProtocolsData Scanning Task Database ManagerTankGate 8315 Software Blocks TankGate Software BlocksParameter Classes Database OrganizationPoint Format Parameter DescriptionParameter Data Formats Common ParametersData Format Description Value Parameter PntCheckSum ParameterPntStatus Parameter Elapse ParameterChange of State-Related Parameters Gathering Point DataStandard Request-Response Format Change of State FormatDeadband Modbus Slave Modbus CommunicationsFixed Modbus Map Function Code Description CommentsAddress Type Number Parameter Data Type Gwblk method 8315 L&J Tankway Software Description TankGate Interface Data Address Parameter Comments Dynamic Parameters Function Configuration Parameters FunctionClock CLK ParametersCommunications COM Configuration Function ParametersApplication Floating Point Register Fpreg Dynamic Function ParametersReal 4 bytes value API Emulator EMUByte value indicating status of point Values are Hex representation of the request sent by the host Configuration Parame Function TersCurrent Command EMU Gateway EmugwDisplays the tank number of the currently selected tank Gauging Systems Inc. Model 2000 Interface GS2000 Last message. The maximum is 255 seconds. The default is Raw2 Gateway Block Gwblk Addr1 is the Data Address and PntRef1 is the corresponding Byte value indicating status of point Values are No errorCRC-16 Checksum of points static Configuration Parameters Size ParameterInteger 2 bytes value Integer Register IregCurrent request message, displayed in hex format Modbus Gateway ModgwCurrent command. Values include Value = Ax + By + Cz + K Scaler Point ScalerDynamic Parame Function Ters Output value for the Scaler pointValue parameter converted to Integer format System Information SYS 17 L&J MCG1000 Tank Gauge LJ1000 PntStatus will be set to indicate the failure Application 18 L&J MCG1500 Tank Gauge LJ1500 Task on the Motherboard determines that the Model 8315 has 8315 L&J Tankway Software Description TankGate Interface 19 L&J MCG2000 Tank Gauge LJ2000 Enables the watchdog task on the Motherboard. The watchdog 8300 20 L&J Scanner Ljscan Command currently being sent to the gaugeNumber of gauge polls since last reset Number of gauge polls which resulted in an errorOut 8315 L&J Tankway Software Description TankGate Interface Installation Safety Guidelines General Safety GuidelinesInstallation Mounting the TankGate inside the enclosure Mounting the TankGateSelect the Unit address Wiring Up PowerInstalling Communications Mounting the EnclosureEstablishing Host Communications Power-UpRS-485 Communications Initial system verificationInstallation TankGate Interface Executing ViewRTU Installing ViewRTUOverview System RequirementsViewRTU Version Selection dialog ViewRTU window ViewRTU Menu BarFile Menu Point Menu Select Point to Add dialog box EditEdit Point selection dialog Edit Point dialog DeletePoint deletion dialog Config Menu Download Database to RTUUpload Database from TankGate Creating a Password To enter the passwordCommunications Menu Changing the PasswordChanging the Password PC SetupStatus Port Communications Setup dialogOptions Menu ConnectTankGate search dialog Import All Convert Configuration FilesConvert ViewRTU versions dialog Export AllHelp Menu Using ViewRTUConfiguring Single Points Edit Digital Point dialog Edit Point Window Push-buttonsMinimize Previous Minimizing the Edit Point WindowConnections NextEdit point parameter value dialog To modify a ValueUpload To modify a valueAdding Multiple Points Configuring Multiple PointsTo modify a Reference Edit point parameter reference dialogAdding Multiple Points Spreadsheet ModePaste Point MenuEdit Menu CopyPaste & Dnld Set ValueSet Value with Auto Increment Options Menu ImportExport View Hide Row/ColParameter Type Description Unhide All Creating and Editing ConnectionsDisplaying the Point Connections window Point Connections WindowTo create a Connection Using ViewRTU TankGate Interface Indicator Condition Run indicator1.3 TXD/RXD LEDs Using the TankGate Push-buttonsCommunications indicator LED Displays under Abnormal ConditionsPress the Reset button Performing a Hard ResetSet the ID DIP switch to the desired addresses Replacing a defective component or module MaintenanceTroubleshooting TankGate Interface 102 Ordering Structure Nema 4 Enclosure Ordering Structure Remote Terminal Unit TankGateModbus Map Value12 Fpreg 3034 3094 8300 Your official representative Your offical representative