Vanguard Managed Solutions 6500 PLUS installation manual Installation, Control Terminal

Page 75

DSU DIM Installation

Installation	Follow these steps to install the DSU DIM:
Procedure

	Step	Action

	1	Install the DSU DIM in the DTE position only (see Figure 2-23).
		The DSU option does not operate if the DIM is installed in the DCE
		position.

	2	Set the jumpers properly.
		This option requires the jumpers be set for the high speed 1 setting
		(M1/HS). This is the same jumper location listed for the V.35, V.36,
		and X.21 interfaces on standalone or Modulus 8/18 hardware.

	3	Plug the EIM into the backplane connector corresponding to the DIM
		port containing the DSU DIM (Port 1 or 2). Verify that the EIM is
		only connected to a port that has a DSU DIM installed.

	4	Tighten the connector mounting screws to provide proper grounding
		and ensure signal integrity.

Caution

Be sure that the telco plug is disconnected before the EIM is disconnected from the 6500PLUS. Also, do not connect the telco plug to the EIM until the EIM has been connected to the 6500PLUS.

Software supporting the DSU option is necessary for the 6500PLUS to recognize the DSU hardware. The provided software requires an NSO or similar equipment to (remotely) download the software, and a Flash card.

Control Terminal	For configuration, reporting, and troubleshooting the CTP port must be used.
Port	Network Management is not supported for the Integral DSU option.

Installation

2-67

Image 75

Contents Vanguard Managed Solutions Restricted Rights Legend Restricted Rights Notification for U.S. Government UsersRadio Frequency Interference Regulations Proprietary MaterialPage Contents Contents About This Manual OverviewThis Chapter Describes Level Mise en gardeChapter Software Features FeaturesProtocols Support Cards HardwareCard Types Processor CardsEnclosures and Backplanes StandaloneEnclosure Types of Modulus Supports OtherVanguardMS Products6500PLUS Processor Cards Port Configurations6525PLUS Network ConcentratorPlus Processor Card Front Panel Hardware 6500PLUS Auxiliary Processor Cards Card Type Works with Port Types Split Speed 6500PLUS Asynchronous and Universal I/O CardsAIO Card UIO CardPlus Universal I/O or Asynchronous I/O Card Front Panel NSO Card 6500PLUS Network Storage Option CardPlus Network Storage Option Card Token Ring Interface Module Trim Card 6500PLUS Token Ring Interface Module OptionHardware DSU Interface 6500PLUS Integral DSUHardware ComponentsPage Chapter Installation OverviewExample Installing Standalone UnitsUnpacking Site PreparationRear View InstallationProcedure Step Action Description/ResultStep Action Replacing Processor Cards in Standalone EnclosuresRemove the Standalone Enclosure Door Bottom of Standalone Enclosure Locking Tabs Using Screwdriver on Locking TabsPlus Processor Card with Retaining Screw Replacement CardStep Action Installing Nodes in Modulus Enclosures AdditionalInformation Operation Multiprocessor NodesMultiprocessor Node ExampleAction Result/Description Replacing Master Processor of Multi-Processor NodeInstalling Nodes in Modulus Enclosures When To Add Another Processor with Flash Before You Begin Adding a Secondary 6500PLUS Processor with FlashStep Action Result/Description Revision Select Enable FlashMaintaining Current SoftwareSelect Copy Software to Flash Upgrading with Software From the New Processor CardModulus 8/18 Installing/Replacing Processor CardsProduct Description Code Requirements for Installing a Trim CardTrim Card Rear Filler Panel for Modulus 8/18 Enclosures Guidelines for Installing a Trim Card in a Modulus 8/18 Trim Card Spacing in a Modulus 18 Enclosure 10. Trim Card Rear Filler Panel for Modulus 9/21 Enclosures Installing Nodes in Modulus Enclosures 11. Trim Card In Left-most Position of Modulus 21 Enclosure Between Two Backplanes EnclosurePlus Installing Nodes in Modulus Enclosures Attaching a Trim Card Installing and Connecting a Trim CardConnecting a Trim Card InstallingCables AttachingTRIM/Processor Card Removing/Replacing Trim CardsBefore Removing Trim CardsModulus 18 with Preparing Modulus Enclosures for RFI SuppressionModulus 18 RFI Installing RFISuppression Screen15. RFI Suppression Straps Modulus 18 No Trim Card No Trim CardModulus 21 RFI SuppressionBar Starting Up the Node Node StartupCtp CR Processor Card Replacing Processor Card ComponentsReplacing DIMs New DIM RemovalJumpers 19. Jumpers on the Port Interface Pins20. Installing Jumpers on the Port Interface Pins Guidelines Installing SIMMs21. Simm Installation Replacing Flash Modules 22. Flash Module Installation Module Replacing ID ModulesChips Replacing Prom ChipsReplacing the Cmem Chip Installing the DSU DSU DIM InstallationControl Terminal Configuring the 6500PLUS for DSU Operation DSU Input and Output Signaling Input SignalsOutput Signals Loopback Options 24. Diagnostics MenuTroubleshooting Troubleshooting DSU DIM InstallationDSU DIM FCC Information Type of InterfaceFacility Interface DSU DIM Installation Event Result/Description Power-Up VerificationChecking LightsDiagnostics Power-UpNode Setting Node to Default ConfigurationInstalling Software Options Status/Statistics Select Node Stat Accessing Node Serial Number from Node StatisticsAccess Serial Number25. Serial Number on Node Stat Screen Steps Enabling a Software Access KeyConfigure Select Software Key Table Follow TheseInstall New Installing New Software Options in an Existing NetworkEnhanced LAN Option Cables Appendix aName Position Function/Signal PinFunction/Signal PinFunction Position Signal Name35/V.36 Modulus 9/21 Enclosures Function PinSignals Modulus 9/21 Enclosures 35/V.36 Signals Standalone and Modulus 8/18 Enclosures Position Name Signals Standalone and Modulus 8/18 EnclosuresPin Function Page Specifications Physical CharacteristicsUnit Dimensions Power Requirements EnvironmentalLimits DIM IndexLL 2-69RS