Vanguard Managed Solutions 6500 PLUS installation manual DSU DIM Installation, Installing the DSU

Page 74

DSU DIM Installation

DSU DIM Installation

Introduction	The DSU DIM is designed to be installed in the DTE position only. The DSU
	option will not operate if the DIM is installed in the DCE position.
	You can install up to two DSUs per platform using both ports 1 and 2.
Example of
Example of	Figure 2-23shows the DSU DIM installation.
Installing the DSU
DIM
	DSU DIM

Front Panel

Port 1

DCE

DTE

DCE

DTE

Port 2

Figure 2-23. DIM Installation

2-66	Installation

Image 74

Contents Vanguard Managed Solutions Restricted Rights Notification for U.S. Government Users Restricted Rights LegendProprietary Material Radio Frequency Interference RegulationsPage Contents Contents This Chapter Describes About This ManualOverview Mise en garde LevelChapter Protocols Software FeaturesFeatures Processor Cards HardwareCard Types Support CardsEnclosure Enclosures and BackplanesStandalone Products Supports OtherVanguardMS Types of Modulus6500PLUS Processor Cards Concentrator Configurations6525PLUS Network PortPlus Processor Card Front Panel Hardware 6500PLUS Auxiliary Processor Cards UIO Card 6500PLUS Asynchronous and Universal I/O CardsAIO Card Card Type Works with Port Types Split SpeedPlus Universal I/O or Asynchronous I/O Card Front Panel 6500PLUS Network Storage Option Card NSO CardPlus Network Storage Option Card 6500PLUS Token Ring Interface Module Option Token Ring Interface Module Trim CardHardware Components 6500PLUS Integral DSUHardware DSU InterfacePage Installation Overview ChapterSite Preparation Installing Standalone UnitsUnpacking ExampleStep Action Description/Result InstallationProcedure Rear ViewReplacing Processor Cards in Standalone Enclosures Step ActionRemove the Standalone Enclosure Door Bottom of Standalone Enclosure Using Screwdriver on Locking Tabs Locking TabsReplacement Card Plus Processor Card with Retaining ScrewStep Action Information Installing Nodes in Modulus EnclosuresAdditional Node Example Multiprocessor NodesMultiprocessor OperationReplacing Master Processor of Multi-Processor Node Action Result/DescriptionInstalling Nodes in Modulus Enclosures Step Action Result/Description When To Add Another Processor with Flash Before You BeginAdding a Secondary 6500PLUS Processor with Flash Current Software Select Enable FlashMaintaining RevisionUpgrading with Software From the New Processor Card Select Copy Software to FlashInstalling/Replacing Processor Cards Modulus 8/18Requirements for Installing a Trim Card Product Description CodeTrim Card Rear Filler Panel for Modulus 8/18 Enclosures Guidelines for Installing a Trim Card in a Modulus 8/18 Trim Card Spacing in a Modulus 18 Enclosure 10. Trim Card Rear Filler Panel for Modulus 9/21 Enclosures Installing Nodes in Modulus Enclosures 11. Trim Card In Left-most Position of Modulus 21 Enclosure Plus Between Two BackplanesEnclosure Installing Nodes in Modulus Enclosures Installing and Connecting a Trim Card Attaching a Trim CardInstalling Connecting a Trim CardAttaching CablesTrim Cards Removing/Replacing Trim CardsBefore Removing TRIM/Processor CardPreparing Modulus Enclosures for RFI Suppression Modulus 18 withScreen Installing RFISuppression Modulus 18 RFINo Trim Card 15. RFI Suppression Straps Modulus 18 No Trim CardBar Modulus 21RFI Suppression Ctp CR Starting Up the NodeNode Startup Replacing Processor Card Components Processor CardReplacing DIMs Removal New DIM19. Jumpers on the Port Interface Pins Jumpers20. Installing Jumpers on the Port Interface Pins Installing SIMMs Guidelines21. Simm Installation Replacing Flash Modules 22. Flash Module Installation Replacing ID Modules ModuleReplacing Prom Chips ChipsReplacing the Cmem Chip DSU DIM Installation Installing the DSUControl Terminal Configuring the 6500PLUS for DSU Operation Output Signals DSU Input and Output SignalingInput Signals 24. Diagnostics Menu Loopback OptionsTroubleshooting DSU DIM Installation TroubleshootingFacility Interface DSU DIM FCC InformationType of Interface DSU DIM Installation Lights Power-Up VerificationChecking Event Result/DescriptionPower-Up DiagnosticsSetting Node to Default Configuration NodeInstalling Software Options Number Accessing Node Serial Number from Node StatisticsAccess Serial Status/Statistics Select Node Stat25. Serial Number on Node Stat Screen Follow These Enabling a Software Access KeyConfigure Select Software Key Table StepsInstalling New Software Options in an Existing Network Install NewEnhanced LAN Option Appendix a CablesPin Function/Signal PinFunction/Signal Name PositionFunction Pin Position Signal Name35/V.36 Modulus 9/21 Enclosures FunctionSignals Modulus 9/21 Enclosures 35/V.36 Signals Standalone and Modulus 8/18 Enclosures Signals Standalone and Modulus 8/18 Enclosures Position NamePin Function Page Unit Dimensions SpecificationsPhysical Characteristics Limits Power RequirementsEnvironmental Index DIMLL 2-69RS