Vanguard Managed Solutions 6500 PLUS installation manual Pin Function

Page 97

P1	P2
1	1

2	3

3	2

4	8

5	14

6	20

7	7

8	4

14	5

15	18

17	24

18	15

20	6

22	25

24	17

25	22

16	21

21	16

Pin	Function
1	Receive+

6	Receive–

5	Transmit–

9	Transmit+

NOTE: All other pins are reserved and should remain unconnected.

Pin	Function
4	Receive+

5	Receive–

3	Transmit–

6	Transmit+

NOTE: All other pins are reserved and should remain unconnected.

Cables

A-7

Image 97

Contents Vanguard Managed Solutions Restricted Rights Legend Restricted Rights Notification for U.S. Government UsersRadio Frequency Interference Regulations Proprietary MaterialPage Contents Contents Overview About This ManualThis Chapter Describes Level Mise en gardeChapter Features Software FeaturesProtocols Card Types HardwareProcessor Cards Support CardsStandalone Enclosures and BackplanesEnclosure VanguardMS Supports OtherProducts Types of Modulus6500PLUS Processor Cards 6525PLUS Network ConfigurationsConcentrator PortPlus Processor Card Front Panel Hardware 6500PLUS Auxiliary Processor Cards AIO Card 6500PLUS Asynchronous and Universal I/O CardsUIO Card Card Type Works with Port Types Split SpeedPlus Universal I/O or Asynchronous I/O Card Front Panel NSO Card 6500PLUS Network Storage Option CardPlus Network Storage Option Card Token Ring Interface Module Trim Card 6500PLUS Token Ring Interface Module OptionHardware Hardware 6500PLUS Integral DSUComponents DSU InterfacePage Chapter Installation OverviewUnpacking Installing Standalone UnitsSite Preparation ExampleProcedure InstallationStep Action Description/Result Rear ViewStep Action Replacing Processor Cards in Standalone EnclosuresRemove the Standalone Enclosure Door Bottom of Standalone Enclosure Locking Tabs Using Screwdriver on Locking TabsPlus Processor Card with Retaining Screw Replacement CardStep Action Additional Installing Nodes in Modulus EnclosuresInformation Multiprocessor Multiprocessor NodesNode Example OperationAction Result/Description Replacing Master Processor of Multi-Processor NodeInstalling Nodes in Modulus Enclosures Adding a Secondary 6500PLUS Processor with Flash When To Add Another Processor with Flash Before You BeginStep Action Result/Description Maintaining Select Enable FlashCurrent Software RevisionSelect Copy Software to Flash Upgrading with Software From the New Processor CardModulus 8/18 Installing/Replacing Processor CardsProduct Description Code Requirements for Installing a Trim CardTrim Card Rear Filler Panel for Modulus 8/18 Enclosures Guidelines for Installing a Trim Card in a Modulus 8/18 Trim Card Spacing in a Modulus 18 Enclosure 10. Trim Card Rear Filler Panel for Modulus 9/21 Enclosures Installing Nodes in Modulus Enclosures 11. Trim Card In Left-most Position of Modulus 21 Enclosure Enclosure Between Two BackplanesPlus Installing Nodes in Modulus Enclosures Attaching a Trim Card Installing and Connecting a Trim CardConnecting a Trim Card InstallingCables AttachingBefore Removing Removing/Replacing Trim CardsTrim Cards TRIM/Processor CardModulus 18 with Preparing Modulus Enclosures for RFI SuppressionSuppression Installing RFIScreen Modulus 18 RFI15. RFI Suppression Straps Modulus 18 No Trim Card No Trim CardRFI Suppression Modulus 21Bar Node Startup Starting Up the NodeCtp CR Processor Card Replacing Processor Card ComponentsReplacing DIMs New DIM RemovalJumpers 19. Jumpers on the Port Interface Pins20. Installing Jumpers on the Port Interface Pins Guidelines Installing SIMMs21. Simm Installation Replacing Flash Modules 22. Flash Module Installation Module Replacing ID ModulesChips Replacing Prom ChipsReplacing the Cmem Chip Installing the DSU DSU DIM InstallationControl Terminal Configuring the 6500PLUS for DSU Operation Input Signals DSU Input and Output SignalingOutput Signals Loopback Options 24. Diagnostics MenuTroubleshooting Troubleshooting DSU DIM InstallationType of Interface DSU DIM FCC InformationFacility Interface DSU DIM Installation Checking Power-Up VerificationLights Event Result/DescriptionDiagnostics Power-UpNode Setting Node to Default ConfigurationInstalling Software Options Access Serial Accessing Node Serial Number from Node StatisticsNumber Status/Statistics Select Node Stat25. Serial Number on Node Stat Screen Configure Select Software Key Table Enabling a Software Access KeyFollow These StepsInstall New Installing New Software Options in an Existing NetworkEnhanced LAN Option Cables Appendix aFunction/Signal Function/Signal PinPin Name Position35/V.36 Modulus 9/21 Enclosures Position Signal NameFunction Pin FunctionSignals Modulus 9/21 Enclosures 35/V.36 Signals Standalone and Modulus 8/18 Enclosures Position Name Signals Standalone and Modulus 8/18 EnclosuresPin Function Page Physical Characteristics SpecificationsUnit Dimensions Environmental Power RequirementsLimits DIM IndexLL 2-69RS