Panasonic CF-35 operating instructions Setting Power Management, Power Management settings

Page 13

Setting Power Management

(How to set [Advanced] and the hibernation timeout)

1 Run the Setup Utility ( page 36)

2 Using

and

, select [Power Management] then press

3 Using and , select [Power Saving] then set [Advanced] with

(To avoid setting the hibernation timeout, press and proceed on to step 6.)

4 Using and , select [Power Switch] then set [Hiberna- tion] with

5 Using and , select [Hibernation Timeout], set either [4

min] or [16 min] with then press 6 Close the Setup Utility ( page 36)

NOTE

If you would like to temporarily disable your power management settings, press +

. When pressed again, or when the computer is restarted (including suspend or hibernation function), the settings are enabled.

Power Management settings

Functions automatically

CPU Speed

HDD Motor

Standby

Power

set

Change Mode

Timeout

Timeout

Management

 

Advanced

 

Enable

1 min

1 min

Standard (Battery/AC adapter)

 

Enable

1 min

2 min

Standard (Battery)*

 

Enable

1 min

2 min

OFF

 

Disable

Never

Never

* Enabled only when the battery itself is being used.

CPU Speed Change Mode : In this mode, the CPU is automatically stopped when there

 

are no operations.

HDD Motor Timeout

: When the hard disk drive is not accessed for more than a

 

minute, power to the motor is shut off.

Standby Timeout

: When the computer is idle or a device is not accessed for

 

one or two minutes, the computer enters the standby mode

 

( page 12).

CAUTION

When you need a network environment.

Be sure to disable hibernation timeout settings in the Setup Utility .

After resuming operation from the hibernation mode, the network connection may be severed or the computer will not work properly.

In communications when a device like a high-speed modem or ISDN terminal adapter is connected to the serial port, etc.

There are times when high-speed communication is adversely affected if the power management

function is enable. Please confirm that is displayed for a few seconds by pressing + to disable the power management function. After you have finished using a communication device, you

can enable the power management function by pressing + .

Key operation and music playback

When the power saving function is running, the keyboard and mouse operations may feel sluggish. Also, music may not play correctly when entering the standby mode during operation.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Operating Instructions Introduction Customers RecordIllustrations in this Manual CopyrightHow to replace the fuse Lithium BatteryFor U.S.A For U.KFor Germany PrecautionsFor France Saving Data on the Hard Disk Read Me FirstSaving Data on Floppy Disks Computer VirusesConfirm the inclusion of all parts First-time OperationDummy FDD Operating Instructions Windows 95 System PackRead the Limited USE Licence Agreement Connect your computer to a power outletHandling the AC adapter ClampsFirst-time Operation Starting Up Starting Up/Shutting DownShutting Down power off your computer Using the Touch PadStarting Up/Shutting Down Starting Up Your Computer QuicklyUsing the hibernation function Using the suspend functionShutting Down Resuming OperationSetting the hibernation timeout Conserving PowerComputing On the Road Things to RememberPower Management settings Setting Power ManagementUse the Battery Indicator to Check on the Battery Status Battery StatusWhen the Remaining Battery Charge Becomes Low Computing On the RoadUsing the Battery Pack Replacing the Battery Pack Using the Battery PackRun the Setup Utility When the User Password is setTo disable your password Re-enter your password at the Enter User Password AgainWhen the coffee break password is set Setting the Coffee break Password enabling or disablingTo disable the Coffee break Password Security MeasuresWhen the supervisor password is set ProcedurePreventing the use of a floppy disk May be OpenedTo disable your supervisor password Setting the Supervisor PasswordEnabling, changing, disabling Preparations for Infrared Data Communications Infrared Data CommunicationsRunning TranXitTM Installing/Removing the Unit Using a CD-ROM DriveInstalling the unit Add-ons/PeripheralsInstalling/Removing the PC Card Using PC CardsInstalling the PC Card Type I orInstalling the RAM module Installing/Removing the RAM ModuleAdd-ons/Peripherals Adding MemoryUsing an External Display Connecting a Port ReplicatorUsing a Printer Installing/Removing the hard disk When flying Usage, Carrying and MaintenanceMaintenance Usage EnvironmentUsing the Self-diagnosis Program List of Error CodesAt the MS-DOS prompt A\WINDOWS\COMMAND, input the following Computer DiagnosisBattery Indicator Dealing with ProblemsStarting Up Display Dealing with ProblemsDisk Operations Character InputConnecting Peripherals Setup UtilityBefore Reinstallation Reinstalling SoftwareReinstalling PreparationPower Management System setupDevice Manager Video driverInstalling TranXit Reinstalling SoftwareInstalling PhoenixCard Manager95 Installing Internet ExplorerIf you want to complete the printer settings, press Windows 95 Setup ProcedureEnter your name and your company’s name, then press If not, pressRunning the Setup Utility Setup UtilityClosing the Program Key OperationsUser Password Main Specifications SpecificationsOther Specifications Names and Functions of Parts Limited USE License Agreement Laufzeit der Lizenz LizenzLicence Contrat de licence dusage limitéTermes, clauses et conditions Index LED indicatorsDFQX2535YA
Top Page Image Contents