Panasonic CF-35 operating instructions Starting Up/Shutting Down

Page 9

Starting Up/Shutting Down

Starting Up

Latch

1 Open up the display

Slide the latch as shown and lift open the display.

NOTE

Do not turn on the computer with the LCD panel closed if an external monitor is not connected. The computer will not power on.

2 Turn your computer on

Move the power switch toward the rear direction and hold one second until the power indicator ( ) goes on before releasing it.

CAUTION

Do not slide the power switch repeatedly.

After you have turned your computer off, you must wait ten seconds before you can turn it back on.

If the computer does not turn on when the power is switched on, the temperature of the CPU has exceeded its normal operating temperature. In this case, a function designed to prevent it from overheating is triggered automatically and prevents the computer from turning on. Should this happen, allow the computer to cool down then switch the power on again.

If the computer still does not turn on, please consult your nearest Panasonic dealer.

If is displayed,

you must first enter your User Password (page 17).

Upon entering your

User Password and

pressing

.

 

If the correct password is input,

Will Start

Over three incorrect attempts,

Will Not Start*

(Power off)

*If you are starting from the suspend mode ( page 10), if after three attempts the correct password is not input, or if no password is entered for about a minute, the computer returns to the suspend mode.

NOTE

If the display on the right appears,

the network password has been set. To read and write data to other computers, the correct password must be entered.

When an application or file that was previously displayed ap- pears on your screen,

this means the suspend or hibernation mode ( page 10) has been set.

3 Select your application

You are able to start working on your computer.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents
Operating Instructions Introduction Customers RecordIllustrations in this Manual CopyrightHow to replace the fuse Lithium BatteryFor U.S.A For U.KPrecautions For GermanyFor France Saving Data on the Hard Disk Read Me FirstSaving Data on Floppy Disks Computer VirusesConfirm the inclusion of all parts First-time OperationDummy FDD Operating Instructions Windows 95 System PackRead the Limited USE Licence Agreement Connect your computer to a power outletHandling the AC adapter ClampsFirst-time Operation Starting Up Starting Up/Shutting DownShutting Down power off your computer Using the Touch PadStarting Up/Shutting Down Starting Up Your Computer QuicklyUsing the hibernation function Using the suspend functionShutting Down Resuming OperationSetting the hibernation timeout Conserving PowerComputing On the Road Things to RememberPower Management settings Setting Power ManagementUse the Battery Indicator to Check on the Battery Status Battery StatusWhen the Remaining Battery Charge Becomes Low Computing On the RoadUsing the Battery Pack Replacing the Battery Pack Using the Battery PackRun the Setup Utility When the User Password is setTo disable your password Re-enter your password at the Enter User Password AgainWhen the coffee break password is set Setting the Coffee break Password enabling or disablingTo disable the Coffee break Password Security MeasuresWhen the supervisor password is set ProcedurePreventing the use of a floppy disk May be OpenedSetting the Supervisor Password To disable your supervisor passwordEnabling, changing, disabling Infrared Data Communications Preparations for Infrared Data CommunicationsRunning TranXitTM Installing/Removing the Unit Using a CD-ROM DriveInstalling the unit Add-ons/PeripheralsInstalling/Removing the PC Card Using PC CardsInstalling the PC Card Type I orInstalling the RAM module Installing/Removing the RAM ModuleAdd-ons/Peripherals Adding MemoryConnecting a Port Replicator Using an External DisplayUsing a Printer Installing/Removing the hard disk When flying Usage, Carrying and MaintenanceMaintenance Usage EnvironmentUsing the Self-diagnosis Program List of Error CodesAt the MS-DOS prompt A\WINDOWS\COMMAND, input the following Computer DiagnosisDealing with Problems Battery IndicatorStarting Up Display Dealing with ProblemsDisk Operations Character InputConnecting Peripherals Setup UtilityBefore Reinstallation Reinstalling SoftwareReinstalling PreparationPower Management System setupDevice Manager Video driverInstalling TranXit Reinstalling SoftwareInstalling PhoenixCard Manager95 Installing Internet ExplorerIf you want to complete the printer settings, press Windows 95 Setup ProcedureEnter your name and your company’s name, then press If not, pressRunning the Setup Utility Setup UtilityClosing the Program Key OperationsUser Password Specifications Main SpecificationsOther Specifications Names and Functions of Parts Limited USE License Agreement Laufzeit der Lizenz LizenzContrat de licence dusage limité LicenceTermes, clauses et conditions Index LED indicatorsDFQX2535YA