Panasonic CF-35 Security Measures, When the User Password is set, Run the Setup Utility

Page 17

Security Measures

To prevent unauthorized access of your computer the various security measures are provided below.

Situation

Function to use

Reference

You do not want your computer to be used without permission

User Password

below

Same as above, but while you’re away temporarily

Coffee break Password

page 18

You want to prevent theft or damage to data by using a floppy disk

Prevent operation by using a floppy disk

page 19

 

Remove floppy disk drive

page 22

You do not want your Supervisor Setup changed without permission

Supervisor Password

page 19

You want to prevent theft of your computer

Use a security lock

page 39

 

 

 

When you do not want your computer to be used without permission

Set the User Password.

Without the password, access to your computer is impossible.

When the User Password is set

Upon entering your User Pass-

If the correct pass-

word and pressing

.

 

word is input,

Will Start

Over three incorrect attempts,

Will Not Start*

(Power off)

* If you are starting from the suspend mode ( page 10), if after three attempts the correct password is not input, or if no password is en- tered for about a minute, the computer returns to the suspend mode.

Setting the user password (enabling, changing, disabling)

1

Run the Setup Utility ( page 36)

2

Using

and

, select [System Setup] then press

3

Using

and

, select [User Password] then press

4 To enable or change your password

Enter your password at the [Enter User Password], then press .

CAUTION

Your password will not be displayed on the screen.

Please limit your password to seven characters. Note that there is no distinction between upper and lower case letters.

White colored keys can be used. Note that space bar and function keys cannot be used.

Do not input your password while holding down on the or . Use only the upper horizontal row of numeric keys to input user pass- words. The numeric keys combined with alphabet keys on the lower key- board cannot be used.

Do not forget your password. If a password is forgotten you will be unable to use your computer.

5

6

7

To disable your password

Using the and keys, select [Delete User Password] then press . Go to step 7.

Re-enter your password at the [Enter User Password Again]

(This is for confirmation purposes.)

Using and , select [Set User Password] then press

At the confirmation screen, press

17

 

Page 16 Page 18
Image 17
Page 16 Page 18
Contents
Operating Instructions Introduction Customers RecordIllustrations in this Manual CopyrightHow to replace the fuse Lithium BatteryFor U.S.A For U.KFor France PrecautionsFor Germany Saving Data on the Hard Disk Read Me FirstSaving Data on Floppy Disks Computer VirusesConfirm the inclusion of all parts First-time OperationDummy FDD Operating Instructions Windows 95 System PackRead the Limited USE Licence Agreement Connect your computer to a power outletHandling the AC adapter ClampsFirst-time Operation Starting Up Starting Up/Shutting DownShutting Down power off your computer Using the Touch PadStarting Up/Shutting Down Starting Up Your Computer QuicklyUsing the hibernation function Using the suspend functionShutting Down Resuming OperationSetting the hibernation timeout Conserving PowerComputing On the Road Things to RememberPower Management settings Setting Power ManagementUse the Battery Indicator to Check on the Battery Status Battery StatusWhen the Remaining Battery Charge Becomes Low Computing On the RoadUsing the Battery Pack Replacing the Battery Pack Using the Battery PackRun the Setup Utility When the User Password is setTo disable your password Re-enter your password at the Enter User Password AgainWhen the coffee break password is set Setting the Coffee break Password enabling or disablingTo disable the Coffee break Password Security MeasuresWhen the supervisor password is set ProcedurePreventing the use of a floppy disk May be OpenedEnabling, changing, disabling Setting the Supervisor PasswordTo disable your supervisor password Running TranXitTM Infrared Data CommunicationsPreparations for Infrared Data Communications Installing/Removing the Unit Using a CD-ROM DriveInstalling the unit Add-ons/PeripheralsInstalling/Removing the PC Card Using PC CardsInstalling the PC Card Type I orInstalling the RAM module Installing/Removing the RAM ModuleAdd-ons/Peripherals Adding MemoryUsing a Printer Connecting a Port ReplicatorUsing an External Display Installing/Removing the hard disk When flying Usage, Carrying and MaintenanceMaintenance Usage EnvironmentUsing the Self-diagnosis Program List of Error CodesAt the MS-DOS prompt A\WINDOWS\COMMAND, input the following Computer DiagnosisStarting Up Dealing with ProblemsBattery Indicator Display Dealing with ProblemsDisk Operations Character InputConnecting Peripherals Setup UtilityBefore Reinstallation Reinstalling SoftwareReinstalling PreparationPower Management System setupDevice Manager Video driverInstalling TranXit Reinstalling SoftwareInstalling PhoenixCard Manager95 Installing Internet ExplorerIf you want to complete the printer settings, press Windows 95 Setup ProcedureEnter your name and your company’s name, then press If not, pressRunning the Setup Utility Setup UtilityClosing the Program Key OperationsUser Password Other Specifications SpecificationsMain Specifications Names and Functions of Parts Limited USE License Agreement Laufzeit der Lizenz LizenzTermes, clauses et conditions Contrat de licence dusage limitéLicence Index LED indicatorsDFQX2535YA