Panasonic CF-35 Connecting a Port Replicator, Using an External Display, Using a Printer

Page 25

Connecting a Port Replicator

A port replicator is available as an option (CF-VEB351). This device eliminates the hassles of having you connect/disconnect the various cables when carrying your computer around and allows a variety of peripherals to be connected including a headphone or microphone, etc.

The port replicator connects to the expansion bus connector on the bottom of your computer. When your computer is not connected to the port replicator, be sure that the expansion bus connector on the bottom of the computer is covered.

For more detailed information, please refer to the operation manual for the port replicator.

Using an External Display

1 Power off your computer ( page 10)

Do not shut down using the suspend or hibernation mode.

CAUTION

Do not install or remove peripherals while your computer is in the suspend or hiber- nation mode; abnormal operation may result.

2 Connect the external display to your computer

Ext. Display Port	NOTE

Using a Printer

Parallel Port

For more detailed information, please refer to the operation manual for the external display.

3 Turn on the display, then turn on your computer

To display on both the LCD of your computer and the external display

1	Run the Setup Utility (			page 36).
2	Using	and	, select [System Setup] then press
3	Using	and	, select [Display], set [Simultaneous] with
4	then press
	Close the Setup Utility (			page 36).
5	Select your external display

Set your external display for [Models] in [Start] - [Settings] - [Control Panel] - [Display] - [Settings] - [Advanced Properties] - [Monitor] - [Change] - [Show all

devices], then press .

1 Power off your computer (page 10)

Do not shut down using the suspend or hibernation mode.

CAUTION

Do not install or remove peripherals while your computer is in the suspend or hiber- nation mode; abnormal operation may result.

2 Connect the printer to your computer

NOTE

Some printer cables may be difficult to connect, and may require removal of the rear cover. Take care not to lose the cover.

3 Turn on the printer, then turn on your computer

25

Image 25

Contents Operating Instructions Introduction Customers RecordIllustrations in this Manual CopyrightHow to replace the fuse Lithium BatteryFor U.S.A For U.KFor Germany PrecautionsFor France Saving Data on the Hard Disk Read Me FirstSaving Data on Floppy Disks Computer VirusesConfirm the inclusion of all parts First-time OperationDummy FDD Operating Instructions Windows 95 System PackRead the Limited USE Licence Agreement Connect your computer to a power outletHandling the AC adapter ClampsFirst-time Operation Starting Up Starting Up/Shutting DownShutting Down power off your computer Using the Touch PadStarting Up/Shutting Down Starting Up Your Computer QuicklyUsing the hibernation function Using the suspend functionShutting Down Resuming OperationSetting the hibernation timeout Conserving PowerComputing On the Road Things to RememberPower Management settings Setting Power ManagementUse the Battery Indicator to Check on the Battery Status Battery StatusWhen the Remaining Battery Charge Becomes Low Computing On the RoadUsing the Battery Pack Replacing the Battery Pack Using the Battery PackRun the Setup Utility When the User Password is setTo disable your password Re-enter your password at the Enter User Password AgainWhen the coffee break password is set Setting the Coffee break Password enabling or disablingTo disable the Coffee break Password Security MeasuresWhen the supervisor password is set ProcedurePreventing the use of a floppy disk May be OpenedTo disable your supervisor password Setting the Supervisor PasswordEnabling, changing, disabling Preparations for Infrared Data Communications Infrared Data CommunicationsRunning TranXitTM Installing/Removing the Unit Using a CD-ROM DriveInstalling the unit Add-ons/PeripheralsInstalling/Removing the PC Card Using PC CardsInstalling the PC Card Type I orInstalling the RAM module Installing/Removing the RAM ModuleAdd-ons/Peripherals Adding MemoryUsing an External Display Connecting a Port ReplicatorUsing a Printer Installing/Removing the hard disk When flying Usage, Carrying and MaintenanceMaintenance Usage EnvironmentUsing the Self-diagnosis Program List of Error CodesAt the MS-DOS prompt A\WINDOWS\COMMAND, input the following Computer DiagnosisBattery Indicator Dealing with ProblemsStarting Up Display Dealing with ProblemsDisk Operations Character InputConnecting Peripherals Setup UtilityBefore Reinstallation Reinstalling SoftwareReinstalling PreparationPower Management System setupDevice Manager Video driverInstalling TranXit Reinstalling SoftwareInstalling PhoenixCard Manager95 Installing Internet ExplorerIf you want to complete the printer settings, press Windows 95 Setup ProcedureEnter your name and your company’s name, then press If not, pressRunning the Setup Utility Setup UtilityClosing the Program Key OperationsUser Password Main Specifications SpecificationsOther Specifications Names and Functions of Parts Limited USE License Agreement Laufzeit der Lizenz LizenzLicence Contrat de licence dusage limitéTermes, clauses et conditions Index LED indicatorsDFQX2535YA