Panasonic CF-35 Computer Diagnosis, List of Error Codes, Using the Self-diagnosis Program

Page 28

Computer Diagnosis

List of Error Codes

If a problem occurs with your hardware, [POST Start up Error(s)] is displayed along with the error code(s), follow the on-screen instructions.

	Setup:	Setup Utility (	page 36) is started. Run [Load Default Settings (PnP)].
		Next the Setup Utility must be run again to input the appropriate operating environ-
		ment settings.
	Exit:	Ignore the error message(s), and restart the computer.

Code				Description
062	Boot failure--default configuration used			Default configuration in use
101	System Board Failure			Interrupt controller failure
102	System Board Failure			Timer 2 test failure
106	System Board Failure			Diskette controller failure
114	Adapter ROM Error			Adapter ROM checksum error
151	System Board Failure			Real-time clock failure
161	Bad CMOS Battery			Dead battery
162	Configuration Change Has Occurred			Configuration error
162	Configuration Error			CMOS checksum error
163	Date and Time Incorrect			Real-time clock is not updating
173	Configuration Change Has Occurred			ROM configuration has changed
201	Memory Size Error			Memory size/data error
301	Keyboard Error			Keyboard failure
303	Keyboard Error			Keyboard controller failure
604	Diskette Drive Error			Diskette drive 0 failure
605	Diskette Drive Error			Diskette unlocked problem
1780	Hard Disk Error			Fixed disk 0 failure
1800	PCI Error			No more IRQs available
1801	PCI Error			No more room for optional ROM
1802	PCI Error			No more I/O space available
1803	PCI Error			No more memory (above 1 MB) available
1804	PCI Error			No more memory (below 1 MB) available
1805	PCI Error			Checksum error or 0 size optional ROM
1962	IPL Error			An operating system could not be found
8601	Pointing Device Error			Pointing device failure
I9990301	IPL Error			Hard disk failure
I9990305	IPL Error			An operating system could not be found

Using the Self-diagnosis Program

Follow the procedure below to check whether each part of your computer is operating properly.

1 To run the program, insert the Firstaid FD you created into the floppy disk drive, then turn your computer on

2 When the display below is shown, select [1. Boot]

1.Boot

2.Restore HDD to factory default (For beginners)

3.Restore HDD to factory default (For advanced users)

3 At the MS-DOS prompt (A:\WINDOWS\COMMAND>), input the following:

diag35

Follow the messages on the screen.

28

Image 28

Contents Operating Instructions Customers Record IntroductionIllustrations in this Manual CopyrightLithium Battery How to replace the fuseFor U.S.A For U.KFor Germany PrecautionsFor France Read Me First Saving Data on the Hard DiskSaving Data on Floppy Disks Computer VirusesFirst-time Operation Confirm the inclusion of all partsDummy FDD Operating Instructions Windows 95 System PackConnect your computer to a power outlet Read the Limited USE Licence AgreementHandling the AC adapter ClampsFirst-time Operation Starting Up/Shutting Down Starting UpUsing the Touch Pad Shutting Down power off your computerStarting Up/Shutting Down Starting Up Your Computer QuicklyUsing the suspend function Using the hibernation functionShutting Down Resuming OperationConserving Power Setting the hibernation timeoutComputing On the Road Things to RememberSetting Power Management Power Management settingsBattery Status Use the Battery Indicator to Check on the Battery StatusWhen the Remaining Battery Charge Becomes Low Computing On the RoadUsing the Battery Pack Using the Battery Pack Replacing the Battery PackWhen the User Password is set Run the Setup UtilityTo disable your password Re-enter your password at the Enter User Password AgainSetting the Coffee break Password enabling or disabling When the coffee break password is setTo disable the Coffee break Password Security MeasuresProcedure When the supervisor password is setPreventing the use of a floppy disk May be OpenedTo disable your supervisor password Setting the Supervisor PasswordEnabling, changing, disabling Preparations for Infrared Data Communications Infrared Data CommunicationsRunning TranXitTM Using a CD-ROM Drive Installing/Removing the UnitInstalling the unit Add-ons/PeripheralsUsing PC Cards Installing/Removing the PC CardInstalling the PC Card Type I orInstalling/Removing the RAM Module Installing the RAM moduleAdd-ons/Peripherals Adding MemoryUsing an External Display Connecting a Port ReplicatorUsing a Printer Installing/Removing the hard disk Usage, Carrying and Maintenance When flyingMaintenance Usage EnvironmentList of Error Codes Using the Self-diagnosis ProgramAt the MS-DOS prompt A\WINDOWS\COMMAND, input the following Computer DiagnosisBattery Indicator Dealing with ProblemsStarting Up Dealing with Problems DisplayDisk Operations Character InputSetup Utility Connecting PeripheralsReinstalling Software Before ReinstallationReinstalling PreparationSystem setup Power ManagementDevice Manager Video driverReinstalling Software Installing TranXitInstalling PhoenixCard Manager95 Installing Internet ExplorerWindows 95 Setup Procedure If you want to complete the printer settings, pressEnter your name and your company’s name, then press If not, pressSetup Utility Running the Setup UtilityClosing the Program Key OperationsUser Password Main Specifications SpecificationsOther Specifications Names and Functions of Parts Limited USE License Agreement Lizenz Laufzeit der LizenzLicence Contrat de licence dusage limitéTermes, clauses et conditions LED indicators IndexDFQX2535YA