Panasonic PT-L6510U manual Interface panel

Page 13

< Interface panel >

 

 

 

 

 

 

 

 

 

 

 

 

IN

 

 

OUT

L

R

IN

OUT

IN

OUT

 

 

 

 

 

 

 

 

 

 

 

IN

OUT

 

S-VIDEO IN

VIDEO

AUDIO IN

RGB

AUDIO

 

USB

SERIAL

 

IN

AUDIO

 

 

 

R/R-Y/PR

G/Y

 

B/B-Y/PB

 

SYNC/HD

VD

 

 

 

 

 

OUT

 

 

 

RGB 1 IN

 

 

 

RGB 2 IN

RGB OUT

REMOTE

WIRED

 

 

IN

DVI-D

OUT

 

 

 

 

> PC <

TBMU152

 

 

 

 

 

 

 

 

S-VIDEO IN port (pages 19, 20, and 33)

Connect an S-video signal source to this port. Depend on input signal, screen aspect will automatically change 16:9 or 4:3.

VIDEO IN port (pages 20 and 22)

Connect a composite video signal source to this port. (BNC)

VIDEO OUT port (pages 20 and 22)

Composite video signal appears at this port. (BNC)

AUDIO IN L-R jacks (page 20)

Only a single pair of audio inputs is available. Change connections to these jacks according to your choice of video source from composite and S-video (RCA jacks).

RGB AUDIO IN jack (pages 20 and 21)

Only a single pair of audio inputs is available. Change connections to these jacks according to your choice of video source from RGB1, RGB2, and DVI-D (M3 jacks).

AUDIO OUT jack (page 20)

The audio signals applied to the AUDIO IN or RGB AUDIO IN jacks of this unit appear at this jack. Once a cable is plugged into this jack, the signal lines to the internal speakers are cut off. (M3 jack)

USB IN ports (pages 16, 21 and 38)

The remote control can be used as your PC mouse by connecting the projector to your PC with the supplied USB cable. (4-pin square connector)

USB OUT ports

The control ports on two or more projectors can be connected to each other for interlocked control operations. (Type B)

SERIAL IN port (pages 20, 21, 22 and 37)

Use the RS-232C serial port as an alternative interface for controlling the projector from your PC. (D-SUB 9 pin)

SERIAL OUT port (pages 21 and 22)

The signal applied to the serial input port appears at this port (9-pin D-sub female connector).

RGB1 (YPBPR) input ports (pages 20, 21 and 22)

Apply RGB or YPBPR video to these ports. (BNC)

RGB2 (YPBPR) IN port (page 21)

RGB video input port. (D-SUB 15 pin)

RGB OUT port (pages 21 and 22)

The signals applied to RGB1 or RGB2 input ports appear at this port (15-pin D-sub female connector).

REMOTE port (page 39)

This port may be used to control the projector from the Remote Control set up in Wired mode. (9-pin D- sub female connector)

DVI-D IN port (pages 19 and 21)

DVI-D signals are applied to this port. (24-pin DVI connector)

DVI-D OUT port (page 21)

The signal applied to the DVI-D input port appears at this port (24-pin DVI connector).

WIRED IN/OUT ports (page 17)

Use to connect multiple PT-L6510U/L6600U projectors in a daisy chain to simultaneously control them from a single wired remote control. (M3 jack)

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents LCD Projector Commercial Use Model No. PT-L6510U PT-L6600UDear Panasonic Customer Important Safety NoticePage Contents Precautions with regard to safety Precautions with regard to safety Do not look into the lens while the projector is being used AccessoriesPrecautions on handling System Example of System upLocation and function of each part Remote ControlProjector Top · Front and Side Projector Top · Rear and Side Rear control panel Location and function of each partInterface panel Loading batteries Using the Remote control unitEffective control range Setting projector IDs for remote control Using laser pointerPress the ID SET button on remote control Laser SpecificationsUsing the remote control as a PC mouse Using the Remote control unitUsing the remote control in wired mode Installation Geometry Setting-upProjection Schemes Projection DistancesSCL Setup precautionsExample of connecting with AV products Setting-upPC with DVI port Control PC USB port Example of connecting with PCsSystem switcher Example of connecting with system switcherMaking Initial Adjustment Setting input port Powering Up the ProjectorPowering Off the Projector Starting to useStarting to use Adjusting the Vertical Position PictureLeveling the Projector Retracting the Leveling FeetUsing the Shutter function Using the Freeze functionAdvice on the installation of exhaust guides Still imageUsing the Digital Zoom D.ZOOM +/- function Menu screens On-screen menusReset the Factory Default Menu Items SettingOn-screen menus Basic Menu OperationsUsing the Index Window function PT-L6510U only Adjusting the picture TV-SYSTEM Signal ModeBAL White balance R/G/B StandardAdjusting the position Aspect What Is S1 Video?Zoom FocusRGB Format Option 1 settingsLens Shift Back ColorLamp Power Option 2 settingsSetting Function 1 Func Lamp SelectSetting Unit ID Option 2 settingsRegistering/Deleting Displaying User Mode Pin assignments and signal names Using the SerialConnection Communication RequirementsControl command Using the SerialCable specifications Connecting to a computerPin assignment and control Using the remote terminalExample of a control panel layout Indication of lamp monitor Indicator Display Condition Check MeasuresCleaning method Cleaning and replacing the air filterReplacing the lamp unit Lamp replacement periodModel No Lamp unit model No Display after 1800 hoursLamp unit replacement steps Replacing the lamp unit Press the Power button to turn off the powerPower does Symptoms ChecksNot turn on No imageSpecifications Video RGB2 input Audio input For RGB 1/2RGB output RemoteAppendix Compatible RGB/YPBPR Signals480 495 7179 476 18 47/64 495 19 31/64 Unit mm inch DimensionsTrademark Trademark acknowledgmentsConcernant LA Sécurité Ne pas couvrir le filtre et la sortie d’air Précautions concernant la sécuritéNe pas surcharger la prise de courant Ne pas retirer le couvercle ou le modifierNe pas placer des récipients de liquide sur le projecteur Ne pas placer le projecteur sur des surfaces instablesNe pas mettre d’objets étrangers dans le projecteur Ne pas placer d’objets lourds sur le projecteur’utiliser que la pile indiquée Précautions concernant la sécuritéAver tissements concernant la manipulation Précautions concernant la manipulationAvant de faire le nettoyage et lentretien, sassurer de Période de remplacement du bloc de lampe Remplacement du bloc de lampeModéls No. Numéro de produit du bloc de lampe ATTENTlONRemplacement de la lampe Procédure de remplacement de la lampeLa lampe est chaude si elle vient d’être utilisée Retirez la porte en la tirant vers l’avantAppuyez sur la touche Power pour couper l’alimentation Technical Support Panasonic Broadcast & Television Systems CompanyPanasonic Canada Inc
Top Page Image Contents