Panasonic PT-L6510U manual Starting to use, Powering Up the Projector, Powering Off the Projector

Page 23

Starting to use

·

·

·

LEVELING Lever

on each side.

Powering Up the Projector

Remove the lens cover.

Plug one end of the accessory power cord into the projector's power receptacle, and the other end to a convenient wall outlet. (AC 100-120 V 50Hz/60 Hz)

Press the “ I ” marked side of the MAIN POWER switch.

The projector will enter standby mode, with the power status light lit in red.

Press the “POWER” button on the projector or “POWER” button on the remote control.

The power indicator on the projector will flash orange. After a shot period, the indicator will illuminate green.

Making Initial Adjustment /

Setting input port

Roughly adjust the focus with the “FOCUS (+/-)” buttons on the rear control panel or with focus ring on the projection lens.

Choose the projection scheme (page 34). Select the input port with the “RGB” or “VIDEO” button. --- [Projector or remote control]

RGB RGB1(YPBPR1)RGB2(YPBPR2)DVI

VIDEO S-VIDEO VIDEO

Adjust volume level with the “VOLUME (+/-)” buttons. --- [Remote control]

For volume level control on the projector, see page 27. If your audio equipment is connected to the AUDIO OUT jack, the VOLUME control adjusts the line output level.

Adjust the projector's tilt angle (page 24).

Adjust the vertical position of the picture (page 24) Press the “AUTO SETUP” button --- [Projector or remote control]

Fit the picture size to the screen size--- [Projector]

Fit the picture size to the screen size with the “ZOOM (+/-)” buttons on the projector's rear control panel.

Repeat steps through until the picture completely fits within the screen bounds.

Adjust focus again with the “FOCUS (+/-)” buttons on the rear control panel or with the focus ring on the projection lens.

Adjust the “ZOOM (+/-)” buttons again until the picture completely fits within the screen bounds.

Powering Off the Projector

1.Press and hold the “POWER” button for more than 0.5 seconds or quickly double-press the button. The projection lamp will turn off, with the power status light turned to orange.

2.Wait until the power status light turns to red (i.e., until the cooling fan stops). While the cooling fan is still running, never switch the MAIN POWER switch OFF, unplug the projector from the outlet, or open the main circuit breaker.

3.Press the “O” marked side of the MAIN POWER switch to remove all power from the projector.

Note

•If the projector is re-powered while the projection lamps are cooling down after the last power off, the lamps will remain off for a short time before they automatically turn on again (Power Status light flashing in orange).

•The projector consumes approx. 9 Watts of power in Standby mode after the cooling fan stops (Power Status light lit in red).

•If you inadvertently shut off the Main Power switch, the projection lamp may remain off for some time on re-powering the projector. The lamp will automatically turn on after a period of time (Power Status light lit in green).

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents LCD Projector Commercial Use Model No. PT-L6510U PT-L6600UDear Panasonic Customer Important Safety NoticePage Contents Precautions with regard to safety Precautions with regard to safety Do not look into the lens while the projector is being used AccessoriesPrecautions on handling System Example of System upLocation and function of each part Remote ControlProjector Top · Front and Side Projector Top · Rear and Side Rear control panel Location and function of each partInterface panel Effective control range Using the Remote control unitLoading batteries Laser Specifications Using laser pointerSetting projector IDs for remote control Press the ID SET button on remote controlUsing the remote control as a PC mouse Using the Remote control unitUsing the remote control in wired mode Projection Distances Setting-upInstallation Geometry Projection SchemesSCL Setup precautionsExample of connecting with AV products Setting-upPC with DVI port Control PC USB port Example of connecting with PCsSystem switcher Example of connecting with system switcherStarting to use Powering Up the ProjectorMaking Initial Adjustment Setting input port Powering Off the ProjectorRetracting the Leveling Feet Adjusting the Vertical Position PictureStarting to use Leveling the ProjectorStill image Using the Freeze functionUsing the Shutter function Advice on the installation of exhaust guidesUsing the Digital Zoom D.ZOOM +/- function Menu screens On-screen menusBasic Menu Operations Menu Items SettingReset the Factory Default On-screen menusUsing the Index Window function PT-L6510U only Adjusting the picture Standard Signal ModeTV-SYSTEM BAL White balance R/G/BAdjusting the position Focus What Is S1 Video?Aspect ZoomBack Color Option 1 settingsRGB Format Lens ShiftLamp Select Option 2 settingsLamp Power Setting Function 1 FuncRegistering/Deleting Displaying User Mode Option 2 settingsSetting Unit ID Communication Requirements Using the SerialPin assignments and signal names ConnectionConnecting to a computer Using the SerialControl command Cable specificationsExample of a control panel layout Using the remote terminalPin assignment and control Indication of lamp monitor Indicator Display Condition Check MeasuresCleaning method Cleaning and replacing the air filterDisplay after 1800 hours Lamp replacement periodReplacing the lamp unit Model No Lamp unit model NoLamp unit replacement steps Replacing the lamp unit Press the Power button to turn off the powerNo image Symptoms ChecksPower does Not turn onSpecifications Remote RGB2 input Audio input For RGB 1/2Video RGB outputAppendix Compatible RGB/YPBPR Signals480 495 7179 476 18 47/64 495 19 31/64 Unit mm inch DimensionsTrademark Trademark acknowledgmentsConcernant LA Sécurité Ne pas retirer le couvercle ou le modifier Précautions concernant la sécuritéNe pas couvrir le filtre et la sortie d’air Ne pas surcharger la prise de courantNe pas placer d’objets lourds sur le projecteur Ne pas placer le projecteur sur des surfaces instablesNe pas placer des récipients de liquide sur le projecteur Ne pas mettre d’objets étrangers dans le projecteur’utiliser que la pile indiquée Précautions concernant la sécuritéAvant de faire le nettoyage et lentretien, sassurer de Précautions concernant la manipulationAver tissements concernant la manipulation ATTENTlON Remplacement du bloc de lampePériode de remplacement du bloc de lampe Modéls No. Numéro de produit du bloc de lampeRemplacement de la lampe Procédure de remplacement de la lampeLa lampe est chaude si elle vient d’être utilisée Retirez la porte en la tirant vers l’avantAppuyez sur la touche Power pour couper l’alimentation Panasonic Canada Inc Panasonic Broadcast & Television Systems CompanyTechnical Support
Top Page Image Contents