Panasonic PT-L6510U manual Lamp unit replacement steps

Page 43

Lamp unit replacement steps

Caution

•After 2000 hours of operating the same lamp, it is only possible to operate the unit for approximately 10 minutes. Replace the lamp and steps 8 to 14 must be completed within 10 minutes:

1.Turn the power off by following the steps on page 23, remove the power plug and confirm that the surroundings of the lamp unit have cooled off.

2.Using a Philips screwdriver, remove the 4 screws on the lamp unit cover located on the rear of the projector.

3.Remove the lamp unit cover by pulling it forward.

Caution

•Be careful not to break the tab located in the center of the lower side of the lamp unit cover.

Fixing screws

Lamp unit cover

Tab

4.Use a Phillips screwdriver to loosen the two lamp unit fixing screws until the screws turn freely. Then hold the handle of the lamp unit and gently pull it out from the projector.

Caution

The lamp unit will be hot after it has been used.

You might get burned if you touch it while it is still hot.

Lamp unit 1

Lamp unit 2

Handle

Lamp unit 1	Lamp unit 2
Fixing screws	Fixing screws

5.Install the new lamp unit.

6.Use a Phillips screwdriver to securely tighten the 2 lamp unit fixing screws.

7.Install the lamp unit cover, and then use a Phillips screwdriver to securely tighten the lamp unit cover fixing 4 screws.

Caution

•Firmly install the lamp unit and lamp unit cover. If not installed firmly, a protection circuit will function and the power will not be turned on.

Fixing screws

PUSH

OPEN

Lamp unit cover

Tab

43

Image 43

Contents LCD Projector Commercial Use Model No. PT-L6510U PT-L6600UDear Panasonic Customer Important Safety NoticePage Contents Precautions with regard to safety Precautions with regard to safety Do not look into the lens while the projector is being used AccessoriesPrecautions on handling System Example of System upLocation and function of each part Remote ControlProjector Top · Front and Side Projector Top · Rear and Side Rear control panel Location and function of each partInterface panel Loading batteries Using the Remote control unitEffective control range Laser Specifications Using laser pointerSetting projector IDs for remote control Press the ID SET button on remote controlUsing the remote control as a PC mouse Using the Remote control unitUsing the remote control in wired mode Projection Distances Setting-upInstallation Geometry Projection SchemesSCL Setup precautionsExample of connecting with AV products Setting-upPC with DVI port Control PC USB port Example of connecting with PCsSystem switcher Example of connecting with system switcherStarting to use Powering Up the ProjectorMaking Initial Adjustment Setting input port Powering Off the ProjectorRetracting the Leveling Feet Adjusting the Vertical Position PictureStarting to use Leveling the ProjectorStill image Using the Freeze functionUsing the Shutter function Advice on the installation of exhaust guidesUsing the Digital Zoom D.ZOOM +/- function Menu screens On-screen menusBasic Menu Operations Menu Items SettingReset the Factory Default On-screen menusUsing the Index Window function PT-L6510U only Adjusting the picture Standard Signal ModeTV-SYSTEM BAL White balance R/G/BAdjusting the position Focus What Is S1 Video?Aspect ZoomBack Color Option 1 settingsRGB Format Lens ShiftLamp Select Option 2 settingsLamp Power Setting Function 1 FuncSetting Unit ID Option 2 settingsRegistering/Deleting Displaying User Mode Communication Requirements Using the SerialPin assignments and signal names ConnectionConnecting to a computer Using the SerialControl command Cable specificationsPin assignment and control Using the remote terminalExample of a control panel layout Indication of lamp monitor Indicator Display Condition Check MeasuresCleaning method Cleaning and replacing the air filterDisplay after 1800 hours Lamp replacement periodReplacing the lamp unit Model No Lamp unit model NoLamp unit replacement steps Replacing the lamp unit Press the Power button to turn off the powerNo image Symptoms ChecksPower does Not turn onSpecifications Remote RGB2 input Audio input For RGB 1/2Video RGB outputAppendix Compatible RGB/YPBPR Signals480 495 7179 476 18 47/64 495 19 31/64 Unit mm inch DimensionsTrademark Trademark acknowledgmentsConcernant LA Sécurité Ne pas retirer le couvercle ou le modifier Précautions concernant la sécuritéNe pas couvrir le filtre et la sortie d’air Ne pas surcharger la prise de courantNe pas placer d’objets lourds sur le projecteur Ne pas placer le projecteur sur des surfaces instablesNe pas placer des récipients de liquide sur le projecteur Ne pas mettre d’objets étrangers dans le projecteur’utiliser que la pile indiquée Précautions concernant la sécuritéAver tissements concernant la manipulation Précautions concernant la manipulationAvant de faire le nettoyage et lentretien, sassurer de ATTENTlON Remplacement du bloc de lampePériode de remplacement du bloc de lampe Modéls No. Numéro de produit du bloc de lampeRemplacement de la lampe Procédure de remplacement de la lampeLa lampe est chaude si elle vient d’être utilisée Retirez la porte en la tirant vers l’avantAppuyez sur la touche Power pour couper l’alimentation Technical Support Panasonic Broadcast & Television Systems CompanyPanasonic Canada Inc