Nortel Networks NN46205-310 quick start DC power supply accessories

Page 26

26Installation preparation

The 8003 chassis provides two slots for installing Ethernet Routing Switch 8600 interface modules and one slot for installing an Ethernet Routing Switch 8691/CPU Module. Slots are numbered from top to bottom.

DC power supply accessories

The DC power supply shipment contains hardware accessories. Use the following checklist to verify the contents of the 8004DC shipping container.

Table 1

8004DC power supply shipping accessories

Check

Accessory

Use to

Two 2-hole crimp	Connect the positive
lug terminals with	and negative power
attached tubing	inputs
(8004)

	One 1-hole crimp		Connect the ground
	lug terminal with		stud
	attached tubing

	5 nuts		Connect all leads

	5 lock washers		Connect all leads

	1 washer		Connect the ground
			stud

Use the following checklist to verify the contents of the 8005DC shipping container.

Table 2

8005DC power supply shipping accessories

	Check	Accessory		Use to

		Three 2-hole crimp		Connect the positive
		lug terminals with		and negative power
		attached tubing		inputs

Nortel Ethernet Routing Switch 8600

Quick Start

NN46205-310 02.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 26

Contents Quick Start Legal Notice Contents Configuration FCC Statement USA only Regulatory Information and Safety PrecautionsInternational Regulatory Statements of Conformity EN 300386 Statement CE Marking Statement Europe only EN 55 022 StatementsEN 55 024 Statement EC Declaration of ConformityVcci Statement Japan/Nippon only Bsmi Statement for 8010, 8006 and 8003 Chassis Taiwan onlyNOM Statement 8010, 8006, and 8003 Chassis Mexico only National Safety Statements of ComplianceCE Marking Statement Europe only EN 60 950 Statement National Safety Statements of Compliance Información NOM unicamente para MéxicoDenan Statement Japan/Nippon only Safety Messages ESDAttenzione ESD Avertissement Peligro Pericolo Regulatory Information and Safety Precautions Software license Nortel Networks Inc. software license agreementGeneral Nortel Networks Inc. software license agreement Software license New in this release FeaturesNortel Command Line Interface Other changesSetting the system date and time using the CLI Connecting the modem using the CLIConnecting the modem using the Nncli Setting the system date and time using the NncliIntroduction NavigationIntroduction Installation preparation Ethernet Routing Switch 8600 slotsDC power supply accessories Personal safety Safety precautionsSafety precautions navigation Check Accessory Use toModule safety Cable and connector safetyElectrostatic discharge safety Risk of equipment damageInstallation preparation Installation Unpacking the chassis Removing a power ﬁller panel Procedure stepsStep Action Risk of personal injury Installing the 8010co chassis in a 19-inch two-post rack PrerequisitesInstalling the 8003, 8006, and 8010 chassis cable guides Installing the top cable-management bracket Installing the side cable-management brackets Procedure job aid Installing the cable-management bracketsGrounding the 8010co chassis Location of ground studs on a 8010co chassis rear panel Installing a moduleProcedure job aid Grounding the 8010co chassis For instructions, see Removing a power filler panel Installing AC power modules Procedure job aid Installing a moduleInstalling DC power modules Installing DC power modules Installation Installing DC power modules End Starting the system Installing a breaker interface panelInstalling a Pcmcia software card Turning on DC power supplies Verifying a successful installation LED power supplyInstallation Connecting a modem using the CLI ConﬁgurationBaud rate 8databits truefalse Mode asciislipppp Variable definitions Variable ValueNumber Pin number Connecting a modem using the NncliDCE DB-25 Boot config sio modem Connecting a VT-100 terminal or PC for local access Procedure job aid config setdate command sample output Setting system date and time using the CLISetting system date and time using the Nncli Procedure job aid clock set command outputChange a password by using the following command Info Oper username Configure password options by using the following command Variable definitionAging-time Conﬁguring the system using the setup utility InstallMaster slot 5/6 Procedure job aid Setup Utility prompt descriptionsPrompt Action Tftp Vlan Risques de blessure corporelle Translation of safety messagesFan tray safety warning message VerletzungsrisikoRischio di lesioni personali Preventing back injury warning statementRisco de ferimento Preventing back injury warning statement Verletzungsrisiko durch Preventing electrical shock warning statementRisques de blessure par choc électrique Riesgo de lesiones por choques eléctricosRischio di lesioni per shock elettrico Preventing hand injury warning statementRisco de ferimento por choque elétrico Risques de blessure provoquée par les pales du ventilateurRisco de ferimento com lâmina do ventilador Safety danger statementRiesgo de lesiones por las aspas del ventilador Rischio di lesioni causate dalle lame del ventilatoreInjury to eye warning statement Risques de blessure oculaire par lumière laserLaser pode causar ferimentos no olho Risiko einer Augenverletzung durchRiesgo de lesión en los ojos por láser Rischio di ustioni agli occhi dovute al laserSafety practices and the hazards danger statement Riesgo de lesión por electrocuciónRisco de ferimentos por choque elétrico Rischio di scosse elettrichePericolo Rischio di scosse elettriche Preventing electric shock danger statement Page Quick Start