Nortel Networks NN46205-310 quick start Installing the 8010co chassis in a 19-inch two-post rack

Page 36

36Installation

4Insert and tighten the rack-mounting screws with a Phillips screwdriver.

--End--

Installing the 8010co chassis in a 19-inch two-post rack

Install the 8010co chassis in a 19-inch two-post rack.

Prerequisites

•Verify that you have the following tools and materials:

—12 Phillips-head screws

—1 Phillips screwdriver

Procedure steps

Step Action

1Place the installation shelf at the bottom of the rack and inside the rails.

2Hold the installation shelf in position and align the shelf mounting rail with the two holes on each side of the vertical rack support.

3Insert a Phillips-head screw through each installation shelf mounting hole and into the corresponding hole in the rack.

Nortel Ethernet Routing Switch 8600

Quick Start

NN46205-310 02.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 36

Contents Quick Start Legal Notice Contents Configuration Regulatory Information and Safety Precautions International Regulatory Statements of ConformityFCC Statement USA only CE Marking Statement Europe only EN 55 022 Statements EN 55 024 StatementEN 300386 Statement EC Declaration of ConformityVcci Statement Japan/Nippon only Bsmi Statement for 8010, 8006 and 8003 Chassis Taiwan onlyNational Safety Statements of Compliance CE Marking Statement Europe only EN 60 950 StatementNOM Statement 8010, 8006, and 8003 Chassis Mexico only National Safety Statements of Compliance Información NOM unicamente para MéxicoDenan Statement Japan/Nippon only Safety Messages ESDAttenzione ESD Avertissement Peligro Pericolo Regulatory Information and Safety Precautions Software license Nortel Networks Inc. software license agreementGeneral Nortel Networks Inc. software license agreement Software license Features Nortel Command Line InterfaceNew in this release Other changesConnecting the modem using the CLI Connecting the modem using the NncliSetting the system date and time using the CLI Setting the system date and time using the NncliIntroduction NavigationIntroduction Installation preparation Ethernet Routing Switch 8600 slotsDC power supply accessories Safety precautions Safety precautions navigationPersonal safety Check Accessory Use toModule safety Cable and connector safetyElectrostatic discharge safety Risk of equipment damageInstallation preparation Installation Unpacking the chassis Removing a power ﬁller panel Procedure stepsStep Action Risk of personal injury Installing the 8010co chassis in a 19-inch two-post rack PrerequisitesInstalling the 8003, 8006, and 8010 chassis cable guides Installing the top cable-management bracket Installing the side cable-management brackets Procedure job aid Installing the cable-management bracketsGrounding the 8010co chassis Installing a module Procedure job aid Grounding the 8010co chassisLocation of ground studs on a 8010co chassis rear panel For instructions, see Removing a power filler panel Installing AC power modules Procedure job aid Installing a moduleInstalling DC power modules Installing DC power modules Installation Installing DC power modules End Installing a breaker interface panel Installing a Pcmcia software cardStarting the system Turning on DC power supplies Verifying a successful installation LED power supplyInstallation Connecting a modem using the CLI ConﬁgurationBaud rate 8databits truefalse Mode asciislipppp Variable definitions Variable ValueConnecting a modem using the Nncli DCE DB-25Number Pin number Boot config sio modem Connecting a VT-100 terminal or PC for local access Setting system date and time using the CLI Setting system date and time using the NncliProcedure job aid config setdate command sample output Procedure job aid clock set command outputChange a password by using the following command Info Oper username Configure password options by using the following command Variable definitionAging-time Conﬁguring the system using the setup utility InstallProcedure job aid Setup Utility prompt descriptions Prompt ActionMaster slot 5/6 Tftp Vlan Translation of safety messages Fan tray safety warning messageRisques de blessure corporelle VerletzungsrisikoPreventing back injury warning statement Risco de ferimentoRischio di lesioni personali Preventing back injury warning statement Preventing electrical shock warning statement Risques de blessure par choc électriqueVerletzungsrisiko durch Riesgo de lesiones por choques eléctricosPreventing hand injury warning statement Risco de ferimento por choque elétricoRischio di lesioni per shock elettrico Risques de blessure provoquée par les pales du ventilateurSafety danger statement Riesgo de lesiones por las aspas del ventiladorRisco de ferimento com lâmina do ventilador Rischio di lesioni causate dalle lame del ventilatoreInjury to eye warning statement Risques de blessure oculaire par lumière laserRisiko einer Augenverletzung durch Riesgo de lesión en los ojos por láserLaser pode causar ferimentos no olho Rischio di ustioni agli occhi dovute al laserSafety practices and the hazards danger statement Riesgo de lesión por electrocuciónRisco de ferimentos por choque elétrico Rischio di scosse elettrichePericolo Rischio di scosse elettriche Preventing electric shock danger statement Page Quick Start