Nortel Networks NN46205-310 quick start Safety practices and the hazards danger statement

Page 77

Safety practices and the hazards danger statement 77

Safety practices and the hazards danger statement

DANGER

Risk of injury by electric shock

Before working on this equipment, be aware of proper safety practices and the hazards involved with electrical circuits. Use only power cords that have a grounding path. Ensure the switch is properly grounded before powering on the unit.

DANGER

DANGER

Risques de blessure par choc électrique

Avant de manipuler cet équipement, vous devez prendre connaissance des pratiques de sécurité appropriées et des risques associés aux circuits électriques. Utilisez uniquement des cordons d’alimentation possédant un conducteur de terre. Assurez-vous que le commutateur est correctement relié à la terre avant de mettre l’unité sous tension.

DANGER

GEFAHR

Verletzungsrisiko durch

Stromschlag Informieren Sie sich über entsprechende Sicherheitsmaßnahmen und die mit Stromkreisen verbundenen Gefahren, bevor Sie mit diesem Gerät arbeiten. Verwenden Sie nur Netzkabel mit Erdungspfad. Stellen Sie sicher, dass der Schalter ordnungsgemäß geerdet ist, bevor Sie das Gerät einschalten.

DANGER

PELIGRO

Riesgo de lesión por electrocución

Antes de trabajar con este equipo, infórmese acerca de las medidas de seguridad adecuadas y de los peligros relacionados con los circuitos eléctricos. Utilice sólo cables de corriente que tengan puesta a tierra. Asegúrese de que el interruptor tenga puesta a tierra antes de encender la unidad.

Nortel Ethernet Routing Switch 8600

Quick Start

NN46205-310 02.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 77
Contents Quick Start Legal Notice Contents Configuration FCC Statement USA only Regulatory Information and Safety PrecautionsInternational Regulatory Statements of Conformity EN 55 024 Statement CE Marking Statement Europe only EN 55 022 StatementsEN 300386 Statement EC Declaration of ConformityBsmi Statement for 8010, 8006 and 8003 Chassis Taiwan only Vcci Statement Japan/Nippon onlyNOM Statement 8010, 8006, and 8003 Chassis Mexico only National Safety Statements of ComplianceCE Marking Statement Europe only EN 60 950 Statement Información NOM unicamente para México National Safety Statements of ComplianceDenan Statement Japan/Nippon only ESD Safety MessagesAttenzione ESD Avertissement Peligro Pericolo Regulatory Information and Safety Precautions Nortel Networks Inc. software license agreement Software licenseGeneral Nortel Networks Inc. software license agreement Software license Nortel Command Line Interface FeaturesNew in this release Other changesConnecting the modem using the Nncli Connecting the modem using the CLISetting the system date and time using the CLI Setting the system date and time using the NncliNavigation IntroductionIntroduction Ethernet Routing Switch 8600 slots Installation preparationDC power supply accessories Safety precautions navigation Safety precautionsPersonal safety Check Accessory Use toCable and connector safety Module safetyRisk of equipment damage Electrostatic discharge safetyInstallation preparation Installation Unpacking the chassis Procedure steps Removing a power filler panelStep Action Risk of personal injury Prerequisites Installing the 8010co chassis in a 19-inch two-post rackInstalling the 8003, 8006, and 8010 chassis cable guides Installing the top cable-management bracket Procedure job aid Installing the cable-management brackets Installing the side cable-management bracketsGrounding the 8010co chassis Location of ground studs on a 8010co chassis rear panel Installing a moduleProcedure job aid Grounding the 8010co chassis For instructions, see Removing a power filler panel Procedure job aid Installing a module Installing AC power modulesInstalling DC power modules Installing DC power modules Installation Installing DC power modules End Starting the system Installing a breaker interface panelInstalling a Pcmcia software card Turning on DC power supplies LED power supply Verifying a successful installationInstallation Configuration Connecting a modem using the CLIBaud rate 8databits truefalse Mode asciislipppp Variable Value Variable definitionsNumber Pin number Connecting a modem using the NncliDCE DB-25 Boot config sio modem Connecting a VT-100 terminal or PC for local access Setting system date and time using the Nncli Setting system date and time using the CLIProcedure job aid config setdate command sample output Procedure job aid clock set command outputChange a password by using the following command Info Oper username Variable definition Configure password options by using the following commandAging-time Install Configuring the system using the setup utilityMaster slot 5/6 Procedure job aid Setup Utility prompt descriptionsPrompt Action Tftp Vlan Fan tray safety warning message Translation of safety messagesRisques de blessure corporelle VerletzungsrisikoRischio di lesioni personali Preventing back injury warning statementRisco de ferimento Preventing back injury warning statement Risques de blessure par choc électrique Preventing electrical shock warning statementVerletzungsrisiko durch Riesgo de lesiones por choques eléctricosRisco de ferimento por choque elétrico Preventing hand injury warning statementRischio di lesioni per shock elettrico Risques de blessure provoquée par les pales du ventilateurRiesgo de lesiones por las aspas del ventilador Safety danger statementRisco de ferimento com lâmina do ventilador Rischio di lesioni causate dalle lame del ventilatoreRisques de blessure oculaire par lumière laser Injury to eye warning statementRiesgo de lesión en los ojos por láser Risiko einer Augenverletzung durchLaser pode causar ferimentos no olho Rischio di ustioni agli occhi dovute al laserRiesgo de lesión por electrocución Safety practices and the hazards danger statementRischio di scosse elettriche Risco de ferimentos por choque elétricoPericolo Rischio di scosse elettriche Preventing electric shock danger statement Page Quick Start