Nortel Networks NN46205-310 quick start Contents

Page 3

.

3

Contents

Regulatory Information and Safety Precautions									5

Software license									17

New in this release									21
Features 21
Other changes 21
Connecting the modem using the CLI				22
Connecting the modem using the NNCLI					22
Setting the system date and time using the CLI						22
Setting the system date and time using the NNCLI							22
Changing passwords using the CLI			22
Changing passwords using the NNCLI				22

Introduction									23

Installation preparation									25
Ethernet Routing Switch 8600 slots			25
DC power supply accessories		26
Safety precautions	27
Personal safety	27

Installation									31
Unpacking the chassis 32
Removing a power filler panel		33
Installing an Ethernet Routing Switch 8003, 8006, or 8010 chassis into a rack									34
Installing the 8010co chassis in a 19-inchtwo-post rack								36
Installing the 8003, 8006, and 8010 chassis cable guides								37
Installing the top cable-management bracket 38
Procedure job aid: Installing the cable-management brackets 39
Installing the side cable-management brackets						39
Grounding the 8010co chassis		40
Procedure job aid: Grounding the 8010co chassis							41
Installing a module	41
Procedure job aid: Installing a module					43
Installing AC power modules		43

Nortel Ethernet Routing Switch 8600

Quick Start

NN46205-310 02.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 3

Contents Quick Start Legal Notice Contents Configuration Regulatory Information and Safety Precautions International Regulatory Statements of ConformityFCC Statement USA only EC Declaration of Conformity CE Marking Statement Europe only EN 55 022 StatementsEN 55 024 Statement EN 300386 StatementBsmi Statement for 8010, 8006 and 8003 Chassis Taiwan only Vcci Statement Japan/Nippon onlyNational Safety Statements of Compliance CE Marking Statement Europe only EN 60 950 StatementNOM Statement 8010, 8006, and 8003 Chassis Mexico only Información NOM unicamente para México National Safety Statements of ComplianceDenan Statement Japan/Nippon only ESD Safety MessagesAttenzione ESD Avertissement Peligro Pericolo Regulatory Information and Safety Precautions Nortel Networks Inc. software license agreement Software licenseGeneral Nortel Networks Inc. software license agreement Software license Other changes FeaturesNortel Command Line Interface New in this releaseSetting the system date and time using the Nncli Connecting the modem using the CLIConnecting the modem using the Nncli Setting the system date and time using the CLINavigation IntroductionIntroduction Ethernet Routing Switch 8600 slots Installation preparationDC power supply accessories Check Accessory Use to Safety precautionsSafety precautions navigation Personal safetyCable and connector safety Module safetyRisk of equipment damage Electrostatic discharge safetyInstallation preparation Installation Unpacking the chassis Procedure steps Removing a power ﬁller panelStep Action Risk of personal injury Prerequisites Installing the 8010co chassis in a 19-inch two-post rackInstalling the 8003, 8006, and 8010 chassis cable guides Installing the top cable-management bracket Procedure job aid Installing the cable-management brackets Installing the side cable-management bracketsGrounding the 8010co chassis Installing a module Procedure job aid Grounding the 8010co chassisLocation of ground studs on a 8010co chassis rear panel For instructions, see Removing a power filler panel Procedure job aid Installing a module Installing AC power modulesInstalling DC power modules Installing DC power modules Installation Installing DC power modules End Installing a breaker interface panel Installing a Pcmcia software cardStarting the system Turning on DC power supplies LED power supply Verifying a successful installationInstallation Conﬁguration Connecting a modem using the CLIBaud rate 8databits truefalse Mode asciislipppp Variable Value Variable definitionsConnecting a modem using the Nncli DCE DB-25Number Pin number Boot config sio modem Connecting a VT-100 terminal or PC for local access Procedure job aid clock set command output Setting system date and time using the CLISetting system date and time using the Nncli Procedure job aid config setdate command sample outputChange a password by using the following command Info Oper username Variable definition Configure password options by using the following commandAging-time Install Conﬁguring the system using the setup utilityProcedure job aid Setup Utility prompt descriptions Prompt ActionMaster slot 5/6 Tftp Vlan Verletzungsrisiko Translation of safety messagesFan tray safety warning message Risques de blessure corporellePreventing back injury warning statement Risco de ferimentoRischio di lesioni personali Preventing back injury warning statement Riesgo de lesiones por choques eléctricos Preventing electrical shock warning statementRisques de blessure par choc électrique Verletzungsrisiko durchRisques de blessure provoquée par les pales du ventilateur Preventing hand injury warning statementRisco de ferimento por choque elétrico Rischio di lesioni per shock elettricoRischio di lesioni causate dalle lame del ventilatore Safety danger statementRiesgo de lesiones por las aspas del ventilador Risco de ferimento com lâmina do ventiladorRisques de blessure oculaire par lumière laser Injury to eye warning statementRischio di ustioni agli occhi dovute al laser Risiko einer Augenverletzung durchRiesgo de lesión en los ojos por láser Laser pode causar ferimentos no olhoRiesgo de lesión por electrocución Safety practices and the hazards danger statementRischio di scosse elettriche Risco de ferimentos por choque elétricoPericolo Rischio di scosse elettriche Preventing electric shock danger statement Page Quick Start