Nortel Networks NN46205-310 quick start Setting system date and time using the CLI

Page 59

Setting system date and time using the NNCLI 59

3Turn on the terminal or PC.

4Log on to the CLI.

--End--

Setting system date and time using the CLI

Set the system date and time using the CLI.

Procedure steps

Action

Set the date of the system by using the following command:

config setdate <MMddyyyyhhmmss>

Procedure job aid: config setdate command sample output

The following is a sample output to verify the config setdate command.

Setting system date and time using the NNCLI

Set the system date and time using the NNCLI.

Prerequisites

•You must log on to the privExec mode.

Procedure steps

Action

Set the system date by using the following command:

clock set <MMddyyyyhhmmss>

Procedure job aid: clock set command output

The following is a sample output to verify the clock set command .

Nortel Ethernet Routing Switch 8600

Quick Start

NN46205-310 02.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 59

Contents Quick Start Legal Notice Contents Configuration FCC Statement USA only Regulatory Information and Safety PrecautionsInternational Regulatory Statements of Conformity EC Declaration of Conformity CE Marking Statement Europe only EN 55 022 StatementsEN 55 024 Statement EN 300386 StatementBsmi Statement for 8010, 8006 and 8003 Chassis Taiwan only Vcci Statement Japan/Nippon onlyNOM Statement 8010, 8006, and 8003 Chassis Mexico only National Safety Statements of ComplianceCE Marking Statement Europe only EN 60 950 Statement Información NOM unicamente para México National Safety Statements of ComplianceDenan Statement Japan/Nippon only ESD Safety MessagesAttenzione ESD Avertissement Peligro Pericolo Regulatory Information and Safety Precautions Nortel Networks Inc. software license agreement Software licenseGeneral Nortel Networks Inc. software license agreement Software license Other changes FeaturesNortel Command Line Interface New in this releaseSetting the system date and time using the Nncli Connecting the modem using the CLIConnecting the modem using the Nncli Setting the system date and time using the CLINavigation IntroductionIntroduction Ethernet Routing Switch 8600 slots Installation preparationDC power supply accessories Check Accessory Use to Safety precautionsSafety precautions navigation Personal safetyCable and connector safety Module safetyRisk of equipment damage Electrostatic discharge safetyInstallation preparation Installation Unpacking the chassis Procedure steps Removing a power ﬁller panelStep Action Risk of personal injury Prerequisites Installing the 8010co chassis in a 19-inch two-post rackInstalling the 8003, 8006, and 8010 chassis cable guides Installing the top cable-management bracket Procedure job aid Installing the cable-management brackets Installing the side cable-management bracketsGrounding the 8010co chassis Location of ground studs on a 8010co chassis rear panel Installing a moduleProcedure job aid Grounding the 8010co chassis For instructions, see Removing a power filler panel Procedure job aid Installing a module Installing AC power modulesInstalling DC power modules Installing DC power modules Installation Installing DC power modules End Starting the system Installing a breaker interface panelInstalling a Pcmcia software card Turning on DC power supplies LED power supply Verifying a successful installationInstallation Conﬁguration Connecting a modem using the CLIBaud rate 8databits truefalse Mode asciislipppp Variable Value Variable definitionsNumber Pin number Connecting a modem using the NncliDCE DB-25 Boot config sio modem Connecting a VT-100 terminal or PC for local access Procedure job aid clock set command output Setting system date and time using the CLISetting system date and time using the Nncli Procedure job aid config setdate command sample outputChange a password by using the following command Info Oper username Variable definition Configure password options by using the following commandAging-time Install Conﬁguring the system using the setup utilityMaster slot 5/6 Procedure job aid Setup Utility prompt descriptionsPrompt Action Tftp Vlan Verletzungsrisiko Translation of safety messagesFan tray safety warning message Risques de blessure corporelleRischio di lesioni personali Preventing back injury warning statementRisco de ferimento Preventing back injury warning statement Riesgo de lesiones por choques eléctricos Preventing electrical shock warning statementRisques de blessure par choc électrique Verletzungsrisiko durchRisques de blessure provoquée par les pales du ventilateur Preventing hand injury warning statementRisco de ferimento por choque elétrico Rischio di lesioni per shock elettricoRischio di lesioni causate dalle lame del ventilatore Safety danger statementRiesgo de lesiones por las aspas del ventilador Risco de ferimento com lâmina do ventiladorRisques de blessure oculaire par lumière laser Injury to eye warning statementRischio di ustioni agli occhi dovute al laser Risiko einer Augenverletzung durchRiesgo de lesión en los ojos por láser Laser pode causar ferimentos no olhoRiesgo de lesión por electrocución Safety practices and the hazards danger statementRischio di scosse elettriche Risco de ferimentos por choque elétricoPericolo Rischio di scosse elettriche Preventing electric shock danger statement Page Quick Start