Nortel Networks NN46205-310 quick start Boot config sio modem

Page 57

Connecting a modem using the NNCLI 57

Procedure steps

Step Action

1Configure port parameters based on the requirements of the modem by using the following command:

boot config sio modem

For information about the configuration requirements of your modem, see the documentation shipped with the modem.

ATTENTION

Nortel recommends that before you configure Serial Line IP (SLIP) or PPP, you become familiar with these protocols.

2If you assign the port mode to slip, use the following command to configure other slip parameters:

boot config sio modem [slip-compression] [slip-rx-compression]

3If you assign the port mode to ppp, use the following commands to configure other ppp parameters:

boot config sio modem [mtu <bytes>] [my-ip <ipaddr>] [peer-ip <ipaddr>] [pppfile <file>]

4Turn off echo mode and return code messaging on the modem.

5Connect the modem to the modem port.

6Save the boot configuration.

7Optionally, shutdown and reinitialize the port by using the following command:

boot config sio modem restart

8Reboot the switch.

 

 

 

--End--

 

 

 

 

Variable definitions

 

 

 

 

 

Variable

Value

 

 

 

 

8databits

Set number of data bits per byte for

 

 

 

software to interpret.

 

 

 

 

baud

Set baud rate for the modem.

 

 

 

 

mode

Set serial port mode.

 

 

 

 

mtu

Sets point-to-point link maximum

 

 

 

transmission unit.

 

 

 

 

my-ip

Sets my IP address on point-to-point link.

 

 

 

 

Nortel Ethernet Routing Switch 8600

Quick Start

NN46205-310 02.01 Standard

30 May 2008

Copyright © 2008 Nortel Networks

Image 57
Contents Quick Start Legal Notice Contents Configuration Regulatory Information and Safety Precautions International Regulatory Statements of ConformityFCC Statement USA only EN 55 024 Statement CE Marking Statement Europe only EN 55 022 StatementsEN 300386 Statement EC Declaration of ConformityBsmi Statement for 8010, 8006 and 8003 Chassis Taiwan only Vcci Statement Japan/Nippon onlyNational Safety Statements of Compliance CE Marking Statement Europe only EN 60 950 StatementNOM Statement 8010, 8006, and 8003 Chassis Mexico only Información NOM unicamente para México National Safety Statements of ComplianceDenan Statement Japan/Nippon only ESD Safety MessagesAttenzione ESD Avertissement Peligro Pericolo Regulatory Information and Safety Precautions Nortel Networks Inc. software license agreement Software licenseGeneral Nortel Networks Inc. software license agreement Software license Nortel Command Line Interface FeaturesNew in this release Other changesConnecting the modem using the Nncli Connecting the modem using the CLISetting the system date and time using the CLI Setting the system date and time using the NncliNavigation IntroductionIntroduction Ethernet Routing Switch 8600 slots Installation preparationDC power supply accessories Safety precautions navigation Safety precautionsPersonal safety Check Accessory Use toCable and connector safety Module safetyRisk of equipment damage Electrostatic discharge safetyInstallation preparation Installation Unpacking the chassis Procedure steps Removing a power filler panelStep Action Risk of personal injury Prerequisites Installing the 8010co chassis in a 19-inch two-post rackInstalling the 8003, 8006, and 8010 chassis cable guides Installing the top cable-management bracket Procedure job aid Installing the cable-management brackets Installing the side cable-management bracketsGrounding the 8010co chassis Installing a module Procedure job aid Grounding the 8010co chassisLocation of ground studs on a 8010co chassis rear panel For instructions, see Removing a power filler panel Procedure job aid Installing a module Installing AC power modulesInstalling DC power modules Installing DC power modules Installation Installing DC power modules End Installing a breaker interface panel Installing a Pcmcia software cardStarting the system Turning on DC power supplies LED power supply Verifying a successful installationInstallation Configuration Connecting a modem using the CLIBaud rate 8databits truefalse Mode asciislipppp Variable Value Variable definitionsConnecting a modem using the Nncli DCE DB-25Number Pin number Boot config sio modem Connecting a VT-100 terminal or PC for local access Setting system date and time using the Nncli Setting system date and time using the CLIProcedure job aid config setdate command sample output Procedure job aid clock set command outputChange a password by using the following command Info Oper username Variable definition Configure password options by using the following commandAging-time Install Configuring the system using the setup utilityProcedure job aid Setup Utility prompt descriptions Prompt ActionMaster slot 5/6 Tftp Vlan Fan tray safety warning message Translation of safety messagesRisques de blessure corporelle VerletzungsrisikoPreventing back injury warning statement Risco de ferimentoRischio di lesioni personali Preventing back injury warning statement Risques de blessure par choc électrique Preventing electrical shock warning statementVerletzungsrisiko durch Riesgo de lesiones por choques eléctricosRisco de ferimento por choque elétrico Preventing hand injury warning statementRischio di lesioni per shock elettrico Risques de blessure provoquée par les pales du ventilateurRiesgo de lesiones por las aspas del ventilador Safety danger statementRisco de ferimento com lâmina do ventilador Rischio di lesioni causate dalle lame del ventilatoreRisques de blessure oculaire par lumière laser Injury to eye warning statementRiesgo de lesión en los ojos por láser Risiko einer Augenverletzung durchLaser pode causar ferimentos no olho Rischio di ustioni agli occhi dovute al laserRiesgo de lesión por electrocución Safety practices and the hazards danger statementRischio di scosse elettriche Risco de ferimentos por choque elétricoPericolo Rischio di scosse elettriche Preventing electric shock danger statement Page Quick Start